Search results
951
[Page extract]
ASTM D5602/D5602M-18
An important factor affecting the performance of many membrane roofing systems is their ability to resist static puncture loads. This test method provides a means for assessing static puncture resistance.
952
[Page extract]
ASTM D953-18
ASTM D953 is a test method that covers the determination of the pin-bearing strength of rigid plastics in either sheet form, molded form, or in reinforced thermoset form.
953
Case study
Wine cork extraction test to ISO 9727-5
Requirement
The customer, AMORIM & IRMÃOS, S.A – Unidade Industrial da Valada, required an economic and easy-to-use system to test the extraction force of corks from glass wine bottles.
954
Case study
End float test of inhaler cap
Requirement
'End float is the displacement in mm of a product', in this case the dispensing cap closure of the inhaler measured at a specific load.
955
Case study
Shoulder prostheses tensile testing
Requirement
Mr Keith Borowsky, an eminent orthopaedic surgeon at the University of Brighton Medical School is developing a new orthopaedic prosthesis for shoulder reconstruction.
957
Case study
Tamper-Proof Closure Test
Requirement
Alcoa required a system to quickly test the tamper-proof rings on soft drink and mineral water closures.
The system had to be easy to operate and allow caps to be loaded quickly.
958
[Page extract]
BS 7548
Describes requirements and test methods for sterile syringes
with or without needles for single use solely for the injection
of insulin in humans. Covers syringes for use with 40 units of
959
[Page extract]
BS ISO 3597-2
ISO 3597-2 specifies a method for determining the flexural strength of composite rods of circular cross-section made of roving-reinforced resin.
960
[Page extract]
Why choose Mecmesin for floating roller peel testing
With decades of experience in materials and force measurement, Mecmesin offers robust and configurable systems that meet industry test standards while adapting to application-specific needs.
961
Case study
Syringe tube pull-off testing
Customised engineering example
Pull-off tensile tests require careful gripping of the separating parts in order to avoid distorting them and therefore artificially weakening the joint.
962
[Page extract]
PD CEN/TR 17394-1
This document provides requirements for security of attachment for clothing components of infant clothing.
963
[Page extract]
Mecmesin solutions for equibiaxial flexure testing
Mecmesin designs and manufactures precision equipment for standards-compliant equibiaxial flexure compression testing, including the concentric ring method. Our systems combine robust mechanical design with advanced control and analysis software.
964
Case study
Fast food tray crush testing
Requirement
As a supplier of fast food trays, the customer needed to make sure that the trays would withstand a certain lateral force without damage to ensure they did not break when being handled and loaded with food.
965
Case study
Cost effective cable strength testing
Customised engineering example
A major manufacturer of wire harnesses and connectors approached us for a cost-effective solution to pull-force test cables with different diameters having direct-bonded joints.
966
[Page extract]
Standards for compressive hardness testing
Internationally recognised standards ensure that compressive hardness tests are accurate, repeatable, and comparable.
967
[Page extract]
Why Mecmesin for material testing solutions
Expertise across diverse sectors
Mecmesin has decades of experience supporting industries from packaging and oral care to pha
968
[Page extract]
ASTM F36-15
The ASTM F36 test method covers the determination of the short-time compressibility and recovery at room temperature of sheet-gasket materials, form-in-place gaskets, and in certain cases, gaskets cut from sheets.
969
Case study
Cosmetics tube flip-cap attachment strength
Customised engineering example
Many flip-caps on flat-sealed cosmetics tubes are not designed for removal by the consumer under normal use.
970
Case study
Torque tester for windows and sunroof controls
Requirement
The customer requested a portable system which would quickly and easily allow him to test the torque required to open and close windows in a car.
971
Case study
Surgical instrument operational torque
Customised engineering example
Endoscopic and laparoscopic surgical instruments are operated by axial and rotating adjustments in the handle, to perform precision movement in the head.
972
Case study
Toy testing to attachment strength safety standards
Requirement
The customer supplies plush giftware to retailers such as Clintons. Their plush products are manufactured to European toy safety standard BS EN 71-1:1998 (Safety of toys - Part 1: Mechanical and physical properties).
973
[Page extract]
Standards for three-point bend testing
Three-point bend testing is governed by established international standards, including:
974
[Page extract]
ASTM C633
This test method covers the determination of the degree of adhesion (bonding strength) of a coating to a substrate or the cohesion strength of the coating in a tension normal to the surface.
975
Case study
Removal torque of cap from drug delivery device
Requirement
Global medical technology company Becton Dickinson (BD) needed to assess the torque required to twist off the cap of a drug delivery device.