Search results
2451
[Page extract]
ASTM D2534
The coefficient of friction is related to the slip properties of many commercial articles that have been coated with petroleum wax (for example, butter cartons and wax-impregnated or hot melt coated corrugated board).
2452
[Page extract]
ISO 9665
Physical property measurement, Chemical analysis and testing, Sampling methods, Specimen preparation, Moisture measurement, Water content determination, Mechanical properties of fluids, Gels, Gelation, Penetration tests, Viscosity measurement, Pipettes,
2453
[Page extract]
CETIE Guide 3
This guide is for producers of quality sparkling wines who carry out the secondary fermentation process in the bottle, also known as bottle fermentation.
2455
[Page extract]
ASTM F1566-09
These test methods cover recognized methods for testing mattress innersprings, boxsprings, and finished mattresses or mattress sets, or both, to ensure uniformity of results.
2456
[Page extract]
SAE J 1553
This SAE Recommended Practice describes a cross peel test method for use in measuring the bonding characteristics of automotive-type adhesives for joining fiber-reinforced plastics to themselves and to metals.
2457
[Page extract]
Hooks
Hooks - round hooks are suitable for samples with loops, such as some springs, O-rings and seals.
Peg hooks can engage smaller attachment holes in thinner and stiffer samples than round hooks.
2458
[Page extract]
*corp Ford DSEU
Test method covering measurement of door slam energy for Ford Chenai, India. Shows Mecmesin loadcell, display and special gripping fixtures. Note: Diagram shows a rigid link bar, which was later replaced by a flexible bungee connection.
2459
[Page extract]
TAPPI T 809
This method describes a procedure for measuring the crushing resistance of a laboratory fluted strip of corrugating medium and provides a means of estimating, in the laboratory, the potential flat crush resistance of a corrugated board.
2460
[Page extract]
BS EN 1125
Ironmongery (buildings), Panic bolts, Bolts (security), Emergency exits, Doors, Fire doors, Safety devices, Closing and check mechanisms, Fire safety in buildings, Means of escape from fire in buildings, Hazard prevention in buildings, Buildings open to
2461
[Page extract]
BS 1881-207
Concretes, Mechanical testing, Surfaces, Field testing, Strength of materials, Testing conditions, Test equipment, Pull-out tests, Penetration tests, Tensile splitting tests, Dimensions.
2462
[Page extract]
ASTM D6958-03
These test methods describe an evaluation procedure for the determination of undesirable side-bonding of coatings for wood flooring.
2463
[Page extract]
BS EN 12430
A compressive point load (of a certain cross-sectional area) is applied to a specimen of thermal insulating product, such as a mineral wool sandwich panel.
2464
[Page extract]
ASTM D5458-95
This test method measures cling between two layers of film, in both a stretched and unstretched condition.
2465
[Page extract]
*corp 01M-01-218
To determine the resistance of seams to slip or break down when placed under a continuous load.
2466
[Page extract]
ASTM C907
This test method covers a laboratory procedure for determining the tensile adhesive strength of a preformed tape sealant. The type of failure can be determined, and the degree of cohesive/adhesive failure can be estimated.
2467
[Page extract]
ASTM E8/E8M-13a
These test methods cover the tension testing of metallic materials in any form at room temperature, specifically, the methods of determination of yield strength, yield point elongation, tensile strength, elongation, and reduction of area.
2468
[Page extract]
BS EN 2243-2
This standard defines the general requirements for the determination of strength of structural adhesives by testing in peel metal to metal joints, at ambient or other temperatures.
2469
[Page extract]
ASTM C1469
This test method covers the determination of shear strength of joints in advanced ceramics at ambient temperature.
2470
[Page extract]
BS EN 5057
Specifies requirements for dimensions, performance characteristics and test programme. section 16 is insertion & withdrawal force test
2471
[Page extract]
ISO 12048
Specifies a method for testing the resistance to compression of complete, filled transport packages and a method for carrying out a stacking test on complete, filled transport packages using the same apparatus.
2472
[Page extract]
EN 14509
This draft European Standard is submitted to CEN members for second formal vote. It has been drawn up by the Technical Committee
CEN/TC 128.
This covers a very wide range of tests including coatings, strengths etc.
2474
[Page extract]
ISO 8510-2
Specifies a 180° peel test for the determination, under specified conditions, of the peel resistance of a bonded assembly of two adherends where one adherend is flexible and the other is rigid.