Search results
2101
[Page extract]
BS EN 862
Packaging. Child resistant packaging. Requirements and testing procedures for non-reclosable packages for non-pharmaceutical products
2102
[Page extract]
BS ISO 6939
Applicable to spun single and folded yarns of any fibre or mixture of fibres manufactured by any spinning systems. Not recommended for testing filament yarns, glass yarns, more complex structures such as cabled yarns or cords.
2103
[Page extract]
EN 14509
This draft European Standard is submitted to CEN members for second formal vote. It has been drawn up by the Technical Committee
CEN/TC 128.
This covers a very wide range of tests including coatings, strengths etc.
2104
[Page extract]
ASTM D790-17
ASTM D790 is used to determine the flexural properties of unreinforced and reinforced plastics, including high modulus composites and electrical insulating materials utilizing a three-point loading system to apply a load to a simply supported beam (spec
2105
[Page extract]
BS 7548
Describes requirements and test methods for sterile syringes
with or without needles for single use solely for the injection
of insulin in humans. Covers syringes for use with 40 units of
2106
[Page extract]
EN 149
EN149 specifies minimum requirements for filtering half masks as respiratory protective devices to protect against particles except for escape purposes.
2107
[Page extract]
ASTM D4760-91
This test method determines the proper resecuring of continuous thread child-resistant closures.
2108
[Page extract]
ISO 594-1
Specification of the requirements for conical (Luer) fittings for use with hyperdemic syringes and needles and with certain other apparatus for medical use such as transfusion and infusion sets.
2109
[Page extract]
ASTM D1004
ASTM D1004-13 covers the determination of tear strength or tear resistance of flexible plastic film and sheeting. The site of tear is initiated by a high stress concentration caused by the 90° angle in the specimen.
2111
[Page extract]
ASTM C480
This test method covers the determination of the creep characteristics and creep rate of flat sandwich constructions loaded in flexure, at any desired temperature.
2112
[Page extract]
ASTM D3469
These test methods measure the downward forces during the disengagement of lug-style caps from their respective containers. The methods measure the maximum torque developed while the cap is further disengaged by turning of the container.
2113
[Page extract]
BS EN ISO 12230
This European Standard specifies a method for the determination of the tensile properties of materials used as surfaces for sports areas.
2114
[Page extract]
ASTM E328-02
These test methods cover the determination of the time dependence of stress (stress relaxation) in materials and structures under conditions of approximately constant constraint, constant environment, and negligible vibration.
2115
[Page extract]
ASTM D4027-98
This test method describes equipment and procedures to measure the shear modulus and shear strength of adhesive layers between rigid adherends.
2116
[Page extract]
ISO 15359
This International Standard specifies, a friction-testing method based on the horizontal plane principle, and the procedure for the determination of the static coefficient of friction before, and static and kinetic coefficients of friction after, a spec
2117
[Page extract]
BS EN ISO 7864
BS EN ISO 7864:2016 specifies requirements for sterile hypodermic needles for single use of designated metric sizes 0,18 mm to 1,2 mm.
2118
[Page extract]
ASTM D4501-01
This test method describes a procedure and fixture used to determine shear strengths of adhesives used to bond materials with moduli higher than the modulus of the adhesive.
2119
[Page extract]
ISO 8094
ISO 8094 specifies a test method for determining the adhesion strength of the cover to the core layer. It applies exclusively to steel cord conveyor belts.
2120
[Page extract]
IEC 61210
IEC 61210:2010 applies to non-insulated flat quick-connect terminations consisting of a male tab of size 2,8 mm, 4,8 mm, 6,3 mm or 9,5 mm with hole or dimple detents and a mating female connector for use as either an incorporated or an integrated part o
2121
[Page extract]
ASTM D1708
ASTM D1708 is used to determine the tensile and elongation properties of small plastic microtensile specimens. These plastic specimens can be of any thickness up to 3.2 mm (1/8 in), including thin films. This test method does not require the use of an
2122
[Page extract]
BS 6319-6
BS 6319-6 is a test method for determining the modulus of elasticity in compression of resin and polymer/cement compositions for use in construction.
2123
[Page extract]
BS EN 12445
This standard specifies the test methods to be applied to a power operated door to demonstrate compliance with the requirements specidied in EN 12453: 2000 in particular it specifies the method of measuring the forces developed by a power operated door.
2124
[Page extract]
ASTM D378
The ASTM D378 test method is used for evaluating the physical properties of flat conveyor belting, which are used in many industrial applications in which they are subjected to a great variety of stresses and conditions.
2125
[Page extract]
BS EN ISO 10066
BS EN ISO 10066 is a test method for determining creep in tension of flexible cellular polymeric materials.