Search results
1251
[Page extract]
ASTM D6117-18
ASTM D6117 covers the evaluation of fastener use with “as manufactured” plastic lumber and shapes through the use of two different testing procedures:
1252
[Page extract]
BS ISO 6133
BS ISO 6133 specifies five methods of calculating, after testing, the tear strength and the adhesion strength of vulcanized rubber or fabrics coated with or adhered to rubber or plastics.
1253
[Page extract]
BS EN ISO 80369-20
These standards describes the methods for testing the performance of 6% Luer lock fittings including assembly, leak tightness, stress cracking, and separation force.
1254
[Page extract]
BS EN ISO 9626
This International Standard specifies the dimensions, surface and mechanical properties of normal- and thin-walled tubing of designated metric sizes 3,4 mm to 0,3 mm, and of extra-thin-walled tubing of designated metric sizes 2,1 mm to 0,6 mm.
1255
[Page extract]
*corp Mastercard CQM: ID-1
Mastercard CQM requirement covers Peel Strength Test (TM-412 #8120#) and Advanced Peel Strength Test (TN-424 #8240#). Methods are based around ISO 10373-1 to determine the peel strength between 2 layers of an ID or security card.
1256
[Page extract]
BS EN 1707
Syringes, Conical fittings (syringes), Injection instruments, Locking and locating devices, Fitting, Pipe fittings, Medical equipment, Medical instruments, Blood transfusion equipment, Dimensions, Dimensional tolerances, Performance testing, Leak tests,
1257
[Page extract]
ASTM D412-16
ASTM D412 is a test standard for testing the tensile stress-strain properties of thermoset rubbers and thermoplastic elastomers. The standard is divided into two test methods.
1258
[Page extract]
ASTM D6742 / D6742M
ASTM D6742 is the standard test method for tensile and compression testing of filled-hole polymer matrix composite laminates. It provides instructions for modifying open-hole tension and compression test methods to determine filled-hole tensile and com
1261
[Page extract]
Baumann tear test
- slit cut laterally in the centre of sample; used to test the tear strength of leather
1262
[Page extract]
Young's modulus
Measure how stiff or elastic a material is under tension or compression with Young’s modulus testing. Universal testing systems provide reliable modulus of elasticity measurements for compliance with global standards like ISO 527 and ASTM D638.
1263
[Page extract]
Needle penetration and drag testing assess the force required to insert a needle into a material and the friction experienced during this process. This test ensures that syringes perform reliably, reducing risks to patients and healthcare providers.
1264
[Page extract]
Ultimate Tensile Strength
What it is, how to measure it, and why it matters
Ultimate tensile strength (UTS) is a critical property used to determine how materials behave under tension. It defines the maximum stress a material can withstand before breaking.
1265
[Page extract]
Abrasion
Abrasion is the surface wear caused by rubbing with another material. The consumer would expect textiles and other products to withstand a certain amount of deterioration.
1266
[Page extract]
Government
The general government sector covers institutions and public bodies where regulations and standards must be strictly adhered to.
1267
Accessory
Cable Cam Grip (large serrated), 5 kN, M10 or M12
432-108
Designed for holding insulated cables and wire. The sample is secured by the serrated cam, which self-tightens as load is applied and minimises the chance of sample slippage.
The grip body features a clearance hole and is supplied with an M10 and M12…
1268
Accessory
Large Single-action Vice Grip, rubber-faced, 2 kN, QC-20 fitting
432-267-V01
A Large Single-action Vice Grip featuring one fixed jaw and one jaw as freely adjustable to mechanically clamp the specimen in place.
Rated to 2 kN in tension with rubber-faced jaws of 78mm wide x 28mm high having an opening of 0-9mm. Provides excellent…
1269
Accessory
Lightweight Mini Vice Grip, 5 N, M6
432-281
By virtue of its spring loaded clamping action the Lightweight Mini Vice Grip is ideal for testing ultra low forces.
Weighing only 30 g it holds specimens without the need to tighten jaws by a thread, which may damage low-capacity loadcells or even the…
1270
Accessory
Cone Point - 8 mm diameter, 500 N, 10-32 UNF
432-358
A Cone Point probe of Ø 8mm with angle of 60°.
For compression testing of various components or materials up to 500 N.
Typically used where compressive force needs to be applied at a point or for penetration into a material over a short distance.…
1271
Accessory
3-Point Bend Jig, 1 kN, Aluminium, T-slot base
432-248
A lightweight 3-point Bend Jig with 60 mm high upper and lower anvils of 1.5mm radius. Has a support span up to 120 mm.
Ideal for most low-force bending and snapping applications.
For use with T-slot base plate (432-294) - sold separately - to fit…
1272
Accessory
Self-levelling Compression Plate Steel - 116 mm, 25 kN, QC-20 fitting
MecS223k-116
MecS223k - 116mm diameter Self-levelling Compression Plate:
Self-levelling allows exact parallelism to be set between the upper and lower plates.. ideal for those applications where it is critical to accurately measure the deformation of a sample.
The…
1273
Accessory
Extended Dovetail Bracket (for AFG or BFG)
432-326
The extended dovetail bracket provides 70 mm of extra daylight when mounting AFG or BFG force gauges to test stands. Fixing screws included.
Note: maximum load 500N
1274
Accessory
Adapter, 10 kN, M10 to M12, M to M
432-335
Male-to-male Adapter
Allows a grip to be connected to a force gauge/loadcell or test stand where thread connections are different.
1275
Accessory
3/8" Lower Chuck Assembly for use on Helixa motor spindle
432-614
A standard self-centering 3-jaw chuck with key.
It has a maximum ⅜" (9.5mm) opening and is connected to the Helixa motor-drive spindle via an adaptor with quick-release grub-screw.
Used to secure a variety of test specimens for torque applications.