Search results
2201
[Page extract]
BS EN 12365-2
Sealing materials, Weatherstrips, Gaskets, Performance, Classification systems, Windows, Doors, Rainwater control systems, Force measurement.
2202
[Page extract]
ISO 12192
Specifies a method for the determination of the edgewise compressive strength (ring crush resistance) of paper and paperboard, especially board used in the manufacture of fibreboard shipping containers.
2203
[Page extract]
ISO 9727-4
ISO 9727-4 specifies a test method for determining the percentage of diameter recovery of cylindrical cork stoppers, after compression.
2204
[Page extract]
BS EN ISO 527-1
BS EN ISO 527-1 specifies the general principles for determining the tensile properties of plastics and plastic composites under defined conditions.
2205
[Page extract]
ASTM F904
ASTM F904 is a test method that covers a procedure for comparing the bond strength or ply adhesion of similar laminates made from flexible materials such as cellulose, paper, plastic film, and foil.
2206
[Page extract]
BS 7320
This British Standard specifies requirements for sharps containers intended to hold potentially infectious medical waste comprised largely of devices which can readily cause physical injury e.g. scalpel blades, hypodermic needles and syringes.
2207
[Page extract]
ISO 11502
Describes a qualitative and a quantitative method for assessing the tendency of flexible plastics films and sheets to adhere to one another when left in contact for some time, at a specified temperature and under light pressure.
2208
[Page extract]
SAE J 1907
This recommended practice defines a procedure for the construction and testing of a 180 deg peel specimen for the purpose of determining the bondability of glass to elastomeric material in automotive modular glass.
2209
[Page extract]
ASTM D143
These test methods cover the determination of various strength and related properties of wood by testing small clear specimens.
2210
[Page extract]
ISO 7623
ISO 7623 specifies a method for determining the bond strength of metal cords to their surrounding coating, either in the initial state or after thermal treatment.
2211
[Page extract]
AEC Q200-005
This specification establishes the procedure and criteria to determine the ability of surface
mounted device terminations and seals to withstand bending, flexing and pulling forces which
2212
[Page extract]
ASTM C1147
ASTM C1147 testing covers the evaluation of joints between two pieces of weldable grades of thermoplastic material. This testing is intended to establish methods to evaluate minimum short term weld factors.
2213
[Page extract]
TAPPI T 556
This procedure is used to measure the bending resistance of paper and paperboard in the machine and cross machine directions, by determining the bending resistance in mN of a 38mm (1.5in) wide vertically clamped sample, at 15o or 7.5o deflection.
2214
[Page extract]
MIL AS23190A
AS23190 is a procurement specification that covers a series of plastic and metal components and devices used for the tying, positioning, and supporting cable, cable assemblies, wire, and wire bundles in electrical, electronic and communication equipment
2215
[Page extract]
ASTM D2633
ASTM D2633 test methods cover procedures for the testing of thermoplastic insulations and jackets used on insulated wire and cable.
2216
[Page extract]
BS EN 12814-1
BS EN 12814-1 is a bend test method for testing welded joints of thermoplastics semi-finished products.
2217
[Page extract]
ASTM F2592
1.1 This test method covers the measurement of force displacement characteristics of a membrane switch.
2218
[Page extract]
ASTM D1709-03
These test methods cover the determination of the energy that causes plastic film to fail under specified conditions of impact of a free-falling dart.
2219
[Page extract]
BS EN ISO 1856
BS EN ISO 1856 is a test method that specifies three methods for determining the compression set of flexible cellular materials and applies only to latex and polyurethane foams of thickness greater than 2 mm.
2220
[Page extract]
ISO 15359
This International Standard specifies, a friction-testing method based on the horizontal plane principle, and the procedure for the determination of the static coefficient of friction before, and static and kinetic coefficients of friction after, a spec
2221
[Page extract]
ASTM D7084-04
1.1 This test method covers the determination of bulk crush strength of a bed of formed catalyst particles 1⁄32 to 3⁄16 in.
2222
[Page extract]
ASTM D575-91
These test methods cover two test procedures for determining the compression-deflection characteristics of rubber compounds other than those usually classified as hard rubber and sponge rubber.
2223
[Page extract]
IFI 543
This standard provides a test method for determining the torque-tension relationship on both external and internal threaded fasteners for the purpose of measuring the frictional characteristics of the threaded fasteners.
2224
[Page extract]
BS EN 2591-418
Describes a method of determining the insertion/extraction forces of female contacts used in elements of electrical and optical connection by means of gauges.