Search results
1251
[Page extract]
BS EN ISO 844
ISO 844 specifies a method of determining a) the compressive strength and corresponding relative deformation, or b) the compressive stress at 10 % relative deformation, and c) when desired, the compressive modulus of rigid cellular plastics.
1252
[Page extract]
CETIE Guide 3
This guide is for producers of quality sparkling wines who carry out the secondary fermentation process in the bottle, also known as bottle fermentation.
1253
[Page extract]
ASTM C1292
This test method covers the determination of shear strength of continuous fiber-reinforced ceramic composites (CFCCs) at ambient temperature.
1254
[Page extract]
ASTM D4541-09e1
This test method uses a class of apparatus known as portable pull-off adhesion testers. They are capable of applying a concentric load and counter load to a single surface so that coatings can be tested even though only one side is accessible.
1255
[Page extract]
Introduction to Delft tear testing
The Delft tear test is a specialised method for determining the tear strength of vulcanised rubber, thermoplastic elastomers and similar flexible materials.
1256
[Page extract]
ASTM D1578
Significance and Use
Test Method D1578 for testing any spun yarn for breaking strength is considered satisfactory for acceptance testing of commercial shipments since the method has been used extensively in the trade.
1257
[Page extract]
ISO 2493-1
Specifies procedures, based on the two-point loading principle, for determining the bending resistance of paper and board.
1258
[Page extract]
Understanding compressive and tensile forces
Insertion and withdrawal testing focuses on two key force measurements:
1259
[Page extract]
MIL 22520-G
This specification covers the general requirements for crimping tools, accessories and inspection gages used for connecting removable contacts (such as; signal, power, coaxial, shielded, thermocouple, and filter pin contacts) coaxial connectors, shielde
1260
[Page extract]
ASTM D6175-03
5.1 This test method is intended to provide information on the ability of an extruded catalyst to retain physical integrity during use.
1261
Bundle
Sharps puncture tester
OmniTest 2.5
BD001
A tester designed for key international standards such as ASTM F2132, BS 7320, and BS 23907 that specify the test procedures for puncture resistance of medical sharps containers.
1262
[Page extract]
Introduction to fabric testing
Fabric testing plays a critical role in quality assurance, helping manufacturers assess the mechanical, physical, and chemical properties of textile materials.
1263
[Page extract]
Introduction to double rip tongue tear testing
Double rip tongue tear testing is a recognised method for assessing the tear resistance of flexible materials including co
1264
[Page extract]
ASTM D6112-18
ASTM D6112 cover the determination of the creep and creep-rupture properties of plastic lumber and shapes, when loaded in compression or flexure under specified environmental conditions. Test specimens in the “as-manufactured” form are employed.
1265
[Page extract]
Mecmesin equipment for 90-degree peel testing
Mecmesin provides a range of test systems designed for peel and adhesion applications:
1267
[Page extract]
ISO 527-5
ISO 527-5 specifies the test conditions for the determination of the tensile properties of unidirectional fibre-reinforced plastic composites, based upon the general principles given in ISO 527-1.
1268
[Page extract]
Tools (calibration related)
To maintain consistent performance and accuracy, tools must be checked regularly.
1269
[Page extract]
ISO 6922
Specifies a method for determining the bond strength of a butt joint when subjected to tensile force. The method is applicable to all types of adhesives.
1270
[Page extract]
Introduction to chord modulus
Chord modulus is a key parameter in material testing, providing engineers and quality control teams with a precise measure of a material’s stiffness under defined loading conditions.
1271
[Page extract]
ASTM D143
These test methods cover the determination of various strength and related properties of wood by testing small clear specimens.
1272
[Page extract]
Take control of your torque testing
Torque testing is a way of determining how an object will react when it is being turned - during normal operation or being twisted until it deliberately fails or breaks.
1273
[Page extract]
Cosmetics & Personal Care Products
Mecmesin solutions for testing in cosmetics and personal care.
Test product formulation for objective texture analysis as well as applicators, dispensers and packaging.
1274
[Page extract]
BS EN 62275
This International Standard specifies requirements for metallic, non-metallic and composite cable ties and their associated fixing devices used for the management and support of wiring systems in electrical installations.
1275
[Page extract]
ASTM D1709-03
These test methods cover the determination of the energy that causes plastic film to fail under specified conditions of impact of a free-falling dart.