Mecmesin | Search results

2226

^{[Page extract]}

ASTM D1710

Among tests for electrical and dimensional (temperature) stability, includes methods for tensile characteristics.

2227

^{[Page extract]}

ISO 527-4 determines the tensile properties of isotropic and orthotropic fibre reinforced plastic composite sheeting and film including the tensile strength and modulus of elasticity, strain, elongation and the tensile energy to break (TEB).

2228

^{[Page extract]}

ASTM E2658-15

These practices cover procedures and requirements for the calibration and verification of testing machine speed by means of standards calibration devices

2229

^{[Page extract]}

ASTM D937-97

1.1 This test method covers measuring with a penetrometer the penetration of petrolatum as an empirical measure of consistency.

2230

^{[Page extract]}

ASTM D3471

This test method covers the determination of the top-load required to engage lugs on Type IA child-resistant closures.

2231

^{[Page extract]}

ASTM F543-13

This specification provides requirements for materials, finish and marking, care and handling, and the acceptable dimensions and tolerances for metallic bone screws that are implanted into bone.

2232

^{[Page extract]}

ASTM D2344 / D2344M

ASTM D2344 is a test method, which determines the short-beam strength of high-modulus fiber-reinforced composite materials. It is applicable to all types of parallel fiber reinforced plastics and composites.

2233

^{[Page extract]}

*corp QPF-MC-1209 B

*Strictly confidential* L'Oreal to methods for shear and penetration testing of lipsticks, deodorants etc.

2234

^{[Page extract]}

ASTM D3826

ASTM D3826 is a tensile test method, which covers a degradation-end point, or a brittle point) for degradable polyethylene/polypropylene films and sheeting less than 1.0 mm thick.

2235

^{[Page extract]}

BS EN 1394

BS EN 1394 is a tensile test method to determine the initial circumferential tensile strength of plastic pipes.

2236

^{[Page extract]}

ASTM D5179-16

ASTM D5179 is a test method for determining organic coatings adhesion to a plastic substrate. It can be used to evaluate the adhesion (pull-off strength) of various coating/substrate combinations e.g. paint and varnish.

2237

^{[Page extract]}

ISO 6789

Wrenches, Torque, Hand tools, Screwdrivers, Marking, Approval testing, Quality control, Calibration

2238

^{[Page extract]}

ISO 10354

Simulates in a qualitative manner the forces and effects on an adhesive-bonded joint at a metal-adhesive/primer interface. It can also be used as a method of checking the surface preparation of substrates.

2239

Sensor

AFTI - Force sensors

Force sensors The AFTI and AFG are versatile force and torque indicators designed for use with the Mecmesin range of 'Smart' tension and compression loadcells. Readings are displayed as live values with peak-hold function in both tension and compression.…

2240

^{[Page extract]}

BS EN 14350-1

Resusable teats and drinking accessories Resusable feeding bottles and drinking cups Single use feeding bottles, feeding teats, feeding bags and drinking accessories, which do not contain fluid when purchased.

2241

^{[Page extract]}

TAPPI T 456

TAPPI T456 is a test method that describes the procedure for the determination of the tensile strength of paper and paperboard after saturation with water.

2242

^{[Page extract]}

FINAT FTM 9

This test method describes a means of assessing probably the most important and yet the hardest to measure property of pressure sensitive materials, the tack.

2243

^{[Page extract]}

ASTM D953-18

ASTM D953 is a test method that covers the determination of the pin-bearing strength of rigid plastics in either sheet form, molded form, or in reinforced thermoset form.

2244

^{[Page extract]}

BS EN ISO 80369-7

This part of ISO 80369 specifies dimensions and requirements for the design and functional performance of small-bore connectors intended to be used for connections in intravascular applications or hypodermic connections in hypodermic applications of med

2245

^{[Page extract]}

ASTM D7084-04

1.1 This test method covers the determination of bulk crush strength of a bed of formed catalyst particles 1⁄32 to 3⁄16 in.

2246

^{[Page extract]}

ASTM C907

This test method covers a laboratory procedure for determining the tensile adhesive strength of a preformed tape sealant. The type of failure can be determined, and the degree of cohesive/adhesive failure can be estimated.

2247

^{[Page extract]}

CETIE Guide 3

This guide is for producers of quality sparkling wines who carry out the secondary fermentation process in the bottle, also known as bottle fermentation.

2248

^{[Page extract]}

BS EN ISO 6789

Wrenches, Torque, Hand tools, Screwdrivers, Marking, Approval testing, Quality control, Calibration

2249

^{[Page extract]}

ASTM C364

This test method covers the compressive properties of structural sandwich construction in a direction parallel to the sandwich facing plane.

2250

^{[Page extract]}

ASTM D4475-02

ASTM D4475 is a test method used for determining the horizontal shear strength of fiber reinforced plastic rods.

Search results

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

Systems

Instruments

Systems

Instruments

Systems

Instruments

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}