Search results
2526
[Page extract]
ASTM C674
These test methods cover determination of the modulus of rupture and the modulus of elasticity of fired ceramic whitewares bodies, formed by any fabrication method, and are applicable to both glazed and unglazed test specimens.
2527
[Page extract]
TAPPI related
TAPPI Standards compared to Related Standards of ISO and ASTM (revised August 2011)
2528
[Page extract]
ISO 7439
ISO 7439:2002 is applicable to single-use copper-bearing intra-uterine contraceptive devices and their insertion instruments.
2529
[Page extract]
ASTM F806-99a
ASTM F806 is a test method that covers determination of the short-time compressibility and recovery at room temperature of laminated composite gasket materials.
2530
[Page extract]
IPC TM-650
A suite of test methods for printed circuit boards. Visual, dimensional, chemical, mechanical, electrical, environmental. To determine the release strength of the carrier of thin copper foil in pounds per inch of width at ambient temperature
2531
[Page extract]
ISO 2555
Specification of a method for determining an apparent viscosity of resins in a liquid state, using one of the types of rotational viskosimeter described in this standard.
2532
[Page extract]
BS EN ISO 3376
This International Standard specifies a method for determining the tensile strength , elongation at a specified load and elongation at break. It is applicable to all types of leather
2533
Event
Materials Testing: Theory and Practice Pt. 1
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
2534
[Page extract]
ASTM D3471
This test method covers the determination of the top-load required to engage lugs on Type IA child-resistant closures.
2535
[Page extract]
AEC Q200-005
This specification establishes the procedure and criteria to determine the ability of surface
mounted device terminations and seals to withstand bending, flexing and pulling forces which
2536
[Page extract]
ASTM D1871
This test method is used to test the strength of adhesion of single-filament wire to vulcanized rubber compounds. It applies to wire made from brass, bronze or zinc coated steel wire.
2537
[Page extract]
TAPPI T 810
This method describes a procedure for measuring the bursting strength of single wall and double wall corrugated board within the range of 690 kPa (100psi) to 4825 kPa (700 psi) employing an instrument which uses a disk shaped, molded diaphragm.
2538
[Page extract]
BS EN 12562
Synthetic fibres, Polyamide fibres, Aramide fibres, Textile products, Textile testing, Yarn, Filament yarns, Filaments, Filament (textile fibre), Yarn testing, Yarn linear density determination, Elongation at fracture, Elongation, Force measurement, Mec
2539
[Page extract]
ASTM D1566
ASTM D1566 is a source of reference for definitions of technical terms used in the rubber industry
Standards can be obtained from appropriate standard authorities.
2540
[Page extract]
BS EN 60352-2
Solderless connectors, Electric connectors, Crimped connectors, Electrical components, Electronic equipment and components, Electrical connections, Communication equipment, Crimping tools, Dimensions, Mechanical crimping, Dimensional measurement, Electr
2541
[Page extract]
SAE AS7928
This specification covers insulated and uninsulated crimp-style copper terminal lugs and conductor splices for stranded conductors. An Amendment corresponding to this standard is available at AS7928_A1
2542
[Page extract]
ISO 3377-2
ISO 3377-2:2016 specifies a method for determining the tear strength of leather using a double-edged tear. The method is sometimes described as the Baumann tear. It is applicable to all types of leather.
2543
[Page extract]
ASTM D1995
These test methods cover procedures by which autohesives can be tested in four commonly practiced stressing modes, namely: compression shear, cleavage, climbing drum peel, and T-peel, and in various combinations of rigid-to-rigid, flexible-to-rigid, and
2544
[Page extract]
ISO 3037
Specifies an unwaxed edge method for the determination of the edgewise crush resistance of corrugated fibreboard. It is applicable to all corrugated fibreboard grades.
2545
[Page extract]
NF S86-604
This document defines the test methods for characterizing metallic watch straps and the corresponding requirements.
2546
[Page extract]
ASTM D7264 / D7264M-15
ASTM D7264 is a test method used to determine the flexural stiffness and strength properties of polymer matrix composites. The test method summarises two procedures:
2547
[Page extract]
ASTM F1473-18
ASTM F1473 is a test method determines the resistance of polyethylene materials to slow crack growth. It is also known as PENT (Pennsylvania Notch Test) test.
2548
[Page extract]
ASTM B913
This test method establishes the requirements for a standardized method of evaluating the quality of crimped-type electrical connections to solid or stranded conductors.
2549
[Page extract]
ASTM F607-03
The ASTM F607 test method provides a means of determining the degree to which gasket materials under compressive load adhere to metal surfaces. The test conditions described are indicative of those frequently encountered in gasket applications.
2550
Specials
Vector instruments - Intuitive touchscreens
Intuitive touchscreen
The most advanced touchscreen force and torque gauges, powered by Vector OS.
Handheld instruments built for tough environments to deliver accuracy and reliability.