Search results
2301
[Page extract]
BS EN 12814-2
BS EN 12814-2 is a tensile test method for testing welded joints of thermoplastics semi-finished products.
2302
[Page extract]
Special compression fixtures
Special compression fixtures have been specially designed to meet the challenges of a particular application.
2303
[Page extract]
BS EN ISO 13262
BS EN ISO 13262 is test method to determine the tensile strength of seams on thermoplastics spirally-formed structured-wall pipes.
2304
[Page extract]
ASTM D747-10
ASTM D747 is used to determine the flexibility of plastics by means of a cantilever beam.
2305
[Page extract]
BS EN ISO 11608-3
Medical equipment, Medical instruments, Parenteral infusion equipment, Injection instruments, Injection guns, Syringes, Drug administration, Measuring cylinders, Containers, Performance testing, Performance, Leak tests, Design, Dimensions
2306
[Page extract]
BS EN ISO 22088-2
BS EN ISO 22088-2 is a test method for determining the environmental stress cracking of plastics.
This has replaced BS EN ISO 6252:1998
2307
[Page extract]
*corp 01M-01-216
To determine the maximum force required to rupture (break) a woven fabric – Rugby only
2308
[Page extract]
ISO 8362-7
This part of ISO 8362 specifies aluminium-plastics combinations for the injection caps of injection vials, as specified in ISO 8362-1 and ISO 8362-4, where the plastics part does not overlap the diameter of the vial body. Section 6.2 Force required to
2309
[Page extract]
ISO 9073-7
Specifies a method for the determination of the bending length of nonwovens. Gives an equation for calculating the flexural rigity of the fabric from the bending length. Does not apply to composites and laminates.
2310
[Page extract]
ISO 15359
This International Standard specifies, a friction-testing method based on the horizontal plane principle, and the procedure for the determination of the static coefficient of friction before, and static and kinetic coefficients of friction after, a spec
2311
[Page extract]
ASTM D7084-04
1.1 This test method covers the determination of bulk crush strength of a bed of formed catalyst particles 1⁄32 to 3⁄16 in.
2312
[Page extract]
BS 1726-1
Provides guidance on methods of specifying and tolerancing hot coiled compression springs, and cold coiled springs that fall outside the size range limits specified in BS EN 15800.
2313
[Page extract]
BS EN 2243-2
This standard defines the general requirements for the determination of strength of structural adhesives by testing in peel metal to metal joints, at ambient or other temperatures.
2314
Event
Medical Devices: General testing with 21 CFR Part 11 compliance
Reliable results, trusted compliance: 21 CFR Part 11's role in securing medical device quality testing.
Quality testing of Medical Devices ranges from syringe actuation (break loose and glide), needle sharpness and adhesion strength to Child R
2315
[Page extract]
ASTM D1876
This test method measures the peel separation strength of two flexible materials that have been bonded together.
2316
[Page extract]
CETIE Guide 4
This document concerns the crowning process, using crown caps for which the seal is provided by a plastic liner, onto glass finishes adapted to either "pry-off" or "twist crown" applications.
2317
Event
Introduction to Consumer Packaging Testing
Damaged packaging can not only cost money but also impact brand perception. Consumers are less likely to purchase a product with damaged packaging, or if their product arrives damaged from poor packaging during the shipping and transport process.
2318
[Page extract]
ISO 29862
This test standard specifies a series of methods for the determination of peel adhesion properties of self adhesives tapes.
2320
[Page extract]
BS EN 862
Packaging. Child resistant packaging. Requirements and testing procedures for non-reclosable packages for non-pharmaceutical products
2321
Page
Contact support
Experiencing an issue or need technical guidance?
Our Support Team is here to help troubleshoot and resolve your problem. Fill out the form and we’ll be in touch as soon as possible.
2322
Event
Essentials of Grip & Fixture Selection Pt. 2
The accuracy of instrument itself- though important, is only one piece of the measurement accuracy puzzle. Grip and fixture selection plays a critical role in the applications in Force and Materials quality testing.
2323
Case study
Insulation film stiffness testing
Customised engineering example
Familiar with three-point bending to test flexural strength properties?
2324
[Page extract]
Wedge grips
Wedge grips - consisting of 2 interchangeable or fixed jaws in the shape of a wedge which are secured in a metal body.