Search results
1926
[Page extract]
BS EN ISO 1806
This standard specifies a method of determining the mesh breaking force of netting for fishing.
1927
[Page extract]
ISO 527-5
ISO 527-5 specifies the test conditions for the determination of the tensile properties of unidirectional fibre-reinforced plastic composites, based upon the general principles given in ISO 527-1.
1928
[Page extract]
Step-by-step guide to conducting a CMT test
Prepare the specimen - Cut to size with clean edges, ensuring flutes remain undamaged, and condition as per the standard.
Calibrate the equipment - Check the load cell and platen alignment.
1929
[Page extract]
BS 2782-3: 360C
BS 2782-3: Method 360C specifies a test method for testing the tear resistance of plastics film and sheeting by the initiation method
1930
[Page extract]
ASTM D2633
ASTM D2633 test methods cover procedures for the testing of thermoplastic insulations and jackets used on insulated wire and cable.
1931
[Page extract]
ISO 12048
Specifies a method for testing the resistance to compression of complete, filled transport packages and a method for carrying out a stacking test on complete, filled transport packages using the same apparatus.
1932
[Page extract]
BS EN 12814-2
BS EN 12814-2 is a tensile test method for testing welded joints of thermoplastics semi-finished products.
1933
[Page extract]
ASTM D7834-13
During the application of coatings, paint brushes can exhibit shedding of filling material onto the coated surface. A measure of this shedding filling material will determine the paint brush’s ability to resist shedding during application.
1934
[Page extract]
ISO 17454
ISO 17454 specifies a method for testing the adhesion between layers of multilayer pipes using a pulling test rig.
1935
[Page extract]
BS EN 12467
Sheet materials, Asbestos cement, Cements, Fibres, Reinforced materials, Sheet roof coverings, Cladding (buildings), Curtain walling, Grades (quality), Density, Strength of materials, Approval testing, Type testing, Quality control, Acceptance inspectio
1936
[Page extract]
Consumer Products
Mecmesin test solutions for products typically found in the home ...
1937
[Page extract]
ASTM D876 - 13
ASTM D876 is a test method covering the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C)2 non-rigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation.
1938
[Page extract]
ASTM C297
This test method determines the flatwise tensile strength of the core, the core-to-facing bond, or the facing of an assembled sandwich panel.
1939
[Page extract]
FINAT FTM1
This test method is designed to quantify the permanence of adhesion or peelability of self-adhesive pressure sensitive) materials.
1940
[Page extract]
Challenges and best practices in peel testing
Common challenges
Material variability in thickness, surface treatment, or adhesive application.
Inconsistent specimen preparation.
Operator error from misalignment or incorrect grip tension.
Best pra
1941
[Page extract]
ASTM F36-15
The ASTM F36 test method covers the determination of the short-time compressibility and recovery at room temperature of sheet-gasket materials, form-in-place gaskets, and in certain cases, gaskets cut from sheets.
1942
[Page extract]
ASTM C961
This test method covers a laboratory procedure for determining the lap shear strength of sealants. It also provides information on the adhesive bond of the sealants to the tested substrates.
1943
[Page extract]
Advances in adhesive testing
Modern systems incorporate high-resolution digital sensors for precise force measurement, real-time data capture with analytical software, and automation to reduce operator influence.
1944
[Page extract]
ASTM D3163
ASTM D3163 is a test method used to determine the single-lap shear adhesive joints of rigid plastic adherends. The test method is useful for generating comparative shear strength data for joints made from a number of plastics.
1945
[Page extract]
ASTM D3983
This test method describes a method of measuring the shear modulus and rupture stress in shear of adhesives in bonded joints.
1946
[Page extract]
IEC 60371-2
Part 1 is definitions of general requirements
Part 3 specifications for individual materials
A number of other non-force/torque properties are tested. This is largely about testing of pressure-bonded laminated materials.
1947
[Page extract]
ASTM D5766 / D5766-M
ASTM D5766 is a test method to determine the open-hole tensile strength of multidirectional polymer matrix composite laminates reinforced by high-modulus fibres.
1948
[Page extract]
ISO 12236
Specifies a method for the determination of the puncture resistance by measuring the force required to push a flat-ended plunger through geosynthetics.
1949
[Page extract]
BS EN 1465
Specifies a method for determining the tensile lap-shear strength of bonded assemblies when tested on a standard specimen and under specified conditions of preparation and testing.