Search results
1776
[Page extract]
BS EN 14704-1
Methods for testing using stripsof fabric in straight strip form or loops, which can be used to measure elasticity and related properties of fabrics, excluding narrow fabrics.
1777
[Page extract]
ASTM D816-06
These test methods cover tests to measure the properties of adhesives, commonly called rubber cements, that may be applied in plastic or fluid form and that are manufactured from natural rubber, reclaimed rubber, synthetic elastomers, or combinations of
1780
[Page extract]
ASTM F1147-05
This test method covers tension testing of calcium phosphate and metallic porous coatings adhering to dense metal substrates at ambient temperatures.
1781
[Page extract]
ASTM D1995
These test methods cover procedures by which autohesives can be tested in four commonly practiced stressing modes, namely: compression shear, cleavage, climbing drum peel, and T-peel, and in various combinations of rigid-to-rigid, flexible-to-rigid, and
1782
[Page extract]
SAE J174
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 1/4 through 1 in nomial diameters.
1783
[Page extract]
ISO 7886-4
This document specifies requirements for sterile single-use hypodermic syringes made of plastic and rubber materials with or without needle, and intended for the aspiration of fluids or for the injection of fluids immediately after filling and of design
1784
[Page extract]
ASTM C203
ASTM C203 is a test method that covers the determination of the breaking load and calculated flexural strength of a rectangular cross section of a preformed block-type thermal insulation tested as a simple beam.
1785
[Page extract]
BS EN 1719
Adhesives, Adhesive strength, Adhesion tests, Paper, Board (paper), Pressure-sensitive materials, Testing conditions, Mathematical calculations
1786
[Page extract]
ISO 1798
ISO 1798 specifies a method for determining the strength and deformation properties of flexible cellular materials when a test piece is extended at a constant rate until it breaks.
This test standard is equivalent to BS EN ISO 1798:2008
1787
[Page extract]
Key standards in compressive deformation testing
Compliance with recognised standards ensures that results are accurate, repeatable, and accepted by regulatory bodies. Examples include:
1788
[Page extract]
ISO 505
ISO 505 specifies a method of test for the measurement of the propagation resistance of an initial tear in textile conveyor belts, either in full thickness or of the carcass only.
1789
[Page extract]
ASTM F1566-09
These test methods cover recognized methods for testing mattress innersprings, boxsprings, and finished mattresses or mattress sets, or both, to ensure uniformity of results.
1790
[Page extract]
ASTM D7617/D7617M-11
This test method specifies the test requirements for (FRP) composite smooth round rods and textured bars for determining the transverse shear strength via a double shear fixture.
1791
[Page extract]
Benefits and limitations of compressive shear testing
Advantages
High precision - accurate measurement of shear strength under controlled compression
<
1792
[Page extract]
ASTM D2979
This test method covers measurement of the pressure-sensitive tack of adhesives.
1793
[Page extract]
ISO 8510-1
Particularly suitable for use with less flexible adherends for which a 180 ° peel test is not suitable because the adherends crack, break or delaminate. A bonded assembly of two adherends is prepared using the adhesive under test.
1794
[Page extract]
Introduction to elongation and recovery testing
In industries working with textiles, rubber, elastomers, and flexible plastics, these properties are directly linked to product reli
1795
[Page extract]
BS EN ISO 8670-2
Two part test on filled bags:
1) 20 N tensile flange seal test, pulled in two directions in turn, at 180 degrees, in shear plane across flange, bag held by transparent custom plate
1796
[Page extract]
ISO 594-2
ISO 594 and EN 1707 contain 8 separate tests, some of which are only applicable to Luer lock fittings. Most of these tests require that the sample be assembled to a particular precision steel reference fitting.
1797
[Page extract]
ASTM D2148
ASTM D2148 is a test standard that for testing bondable silicone rubber tapes, which form a sealed structure either with the application of heat (and pressure if needed) or by the process of auto-adhesion (self-fusing).
1798
[Page extract]
PSTC 8
Unwind adhesion is a quantitative measure of the degree of ease or difficulty in unwinding a roll of tape.
The test specimen shall be any 10 m (10 yard) or more roll of pressure sensitive tape - preferably 24 mm (1”) wide.
1799
[Page extract]
ASTM D3807
ASTM D3807 is a test method used to determine the strength properties of adhesives in cleavage peel by tension loading. It allows the comparative testing of cleavage/peel strengths of bonded engineering thermoplastic adherends.
1800
[Page extract]
BS EN 1393
BS EN 1393 specifies a test method for testing the longitudinal tensile properties of glass-reinforced thermosetting plastics (GRP) pipes.