Search results
626
[Page extract]
CETIE Guide 2
This guide applies to the screw capping of non-carbonated beverages and products with a metallic tamper-evident closure. Bottles may also be fitted with an in-bore insert for product flow control or to prevent re-filling.
627
Case study
Anchorage strength testing of roots for resistance to lodging
Requirement
A leading Dutch University wanted to improve the yield and quality of a gluten-free cereal crop named Teff (Eragrostistef). Teff is an ancient grain that originates from Ethiopia and is now grown in Europe.
628
Case study
Peel test of semi-rigid packaging for medical device
Customised engineering example
Our client needed to test the peeling quality of a Tyvek® paper lid used to seal a sterile, semi-rigid thermoformed plastic tray containing pre-filled syringes.
629
Case study
Electrical connector insertion and withdrawal forces
Customised engineering example
Push-fit electrical connectors with hole or dimple detents (also known as 'spade terminals') must offer a firm but practical fit.
630
[Page extract]
ASTM D624-00
This test method describes procedures for measuring a property of conventional vulcanized rubber and thermoplastic elastomers called tear strength.
631
Case study
Diamante pull-off test
Requirement
The customer was a supplier to major UK clothing retailer Marks & Spencer, who stipulate that all fasteners and attachments must be tested to failure.
632
[Page extract]
TAPPI T 400
This method describes procedures for obtaining a representative sample for testing.
633
Event
Compressive Crush Force Testing
This webinar will focus on identifying and troubleshooting variables that impact compressive force testing, setting up repeatable compression force tests and establishing consistent testing standards for your products.
634
Case study
Medical suture device calibration system
Requirement
A number of devices which 'crimp' a curved needle to a fine medical thread needed to be tested. The crimp force was applied horizontally pulling a lever on the device.
635
Case study
Insulation film stiffness testing
Customised engineering example
Familiar with three-point bending to test flexural strength properties?
636
[Page extract]
ASTM C165
1.1 This test method covers two procedures for determining the compressive resistance of thermal insulations.
637
[Page extract]
ASTM F2132-01
This specification provides the performance requirements and associated test procedures for the puncture resistance of materials used in the construction of containers for discarded medical needles and other sharps.
638
Case study
Torsion spring testing
Customised engineering example
Unlike most compression and tension springs, torsion springs are produced in a variety of forms with differing leg positions.
639
[Page extract]
ASTM C1147
ASTM C1147 testing covers the evaluation of joints between two pieces of weldable grades of thermoplastic material. This testing is intended to establish methods to evaluate minimum short term weld factors.
640
[Page extract]
ASTM D5034-09
This test method covers the grab and modified grab test procedures for determining the breaking strength and elongation of most textile fabrics. Provisions are made for wet testing.
641
Case study
Closure torque validation
Requirement
The customer had a number of Tornado closure torque testers, and wished to carry out regular validation checks without the need to return the units to either Mecmesin or an approved laboratory.
642
Case study
Tensile test on footwear materials
Requirement
William Lamb Footwear is one of the UK's leading footwear distributors. A test system was required to measure and ensure that the footwear and its components passed quality standards set out by their end-customers.
644
Case study
Inline respiratory filter pull test
Customised engineering example
A manufacturer of filtration products needed to test the extraction force of a respiratory filter when pulled from within an inline medical device.
645
Case study
Card and paper crease line testing
Customised engineering example
A packaging production company needed to test the crease force of the ink-coated card used in their fully-enclosed cartons.
646
[Page extract]
ASTM D7137 / D7137M-17
ASTM D7137 is a test method that measures the compression residual strength properties of multidirectional polymer matrix composite laminated plates, which have been subjected to quasi-static indentation
647
Event
Medical Devices – Syringe & Needle Testing Fundamentals
Vial sealing is a critical step in the process of ‘fill and finish’ operations for vaccines and medications, as it defines the seal quality of the final product, ensuring sterility and preventing leakage.
648
Case study
Child safety - force to extract lighter
Requirement
The customer manufactures lighters and is currently developing a case/guard designed to increase the safety for children.
649
Event
Fundamentals of Texture Testing Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
650
Case study
Box crush test (BCT) and transit packaging compression testing
Customised engineering example
Boxes for the consumer and transit packaging industries must be as light as possible whilst still retaining a robustness to contain and protect their contents and also have the strength to stand up to shipping, ha