Search results
1876
[Page extract]
Analysing and interpreting results
Results are expressed as the maximum load sustained by the sample. This can be converted into a ring crush index by dividing by the specimen width.
1877
[Page extract]
Standards and regulations in shear testing
Several industry standards and protocols govern food shear testing, ensuring repeatable results and regulatory compliance. Examples include:
1878
[Page extract]
Speak to an expert
If you need to implement flat crush testing for corrugated fibreboard in line with international standards, Mecmesin can provide the right equipment, fixtures, and expertise.
1879
[Page extract]
Understanding test standards: industry-specific requirements
To maintain consistency and reliability, compressive strength tests are often governed by established standards.
1880
[Page extract]
Common challenges in fastening torque
Believing tighter is always better, leading to over-torquing.
Ignoring lubrication effects, which can reduce the torque needed for the same clamping force.
Relying on uncalibrated hand tools, which can produce inconsistent res
1881
[Page extract]
Introduction to compressive shear testing
Compressive shear testing is a mechanical test method used to measure a material’s ability to resist shear forces while under compressive load.
1882
[Page extract]
Introduction to strain at maximum stress testing
Strain at maximum stress testing is a critical method in material evaluation, providing a precise measurement of how much a material deforms at the point of its highest applied load.
1883
[Page extract]
Introduction to peel wheel testing
The peel wheel test is a specialised adhesion test method used to measure the strength of adhesive bonds in flexible materials such as plastics, films, and laminates.
1884
Test Frame
OmniTest test frame (single column)
OmniTest test frame
A single-column motorised test frame designed to apply tensile, shear, flexural and compressive forces from 2 N right up to a capacity of 7.5 kN (1686 lbf).Its versatile construction makes it perfectly suited for testing all kinds of…
1885
[Page extract]
Plates
Compression fixtures should be selected to suit the contact area of the sample which is to be tested.
1886
[Page extract]
Energy
Mecmesin has long been providing force and torque testing solutions to suppliers and contractors into the energy industry...
1887
[Page extract]
Architectural
Force and torque testing within the architectural industry primarily involve the testing of architectural hardware and access control systems, to ensure operational forces are within the limits stipulated by various guidelines and test standards, eg&nbs
1888
[Page extract]
Jewellery & Watch
In jewellery and watch production, alloys, components and other materials must meet the needs of the manufacturing process and the end-product should give good service performance when worn by the customer.
1889
Test Frame
MultiTest-dV test frame
MultiTest-dV test frame
A ballscrew-driven motorised test frame designed to apply tension and compression from 2 N right up to a capacity of 2.5 kN (550 lbf).Its versatile construction makes it perfectly suited for testing all kinds of components in a…
1890
Test Frame
Helixa test frame
Helixa test frame
A precision motorised test frame designed to apply torque from a few mN.m right up to a capacity of 6 N.m. (50 lbf.in).Its sensitivity and axial alignment make it perfectly suited for testing fine-precision components in a quality…
1891
Sensor
Sensors - Vortex
Torque sensors (ITC)
The ITC range of interchangeable torque sensors is specially adapted for the Vortex-i and -xt test systems. Plug and play for automatic calibration and available in 5 different capacities for all requirements, from 0 - 0.3 N.m (0 - 2.…
1892
Test Frame
MultiTest test frame (single column)
MultiTest test frame
A ballscrew-driven motorised test frame designed to apply tension and compression from 2 N right up to a capacity of 5 kN (1100 lbf).Its versatile construction makes it perfectly suited for testing all kinds of components in a quality…
1893
Test Frame
OmniTest test frame (twin column)
OmniTest test frame
A motorised test frame driven by twin ballscrews featuring dual-columns and designed to apply tension and compression from 2 N right up to a capacity of 50 kN (11000 lbf).Its versatile construction makes it perfectly suited for testing…
1894
[Page extract]
Standards for the 90-degree peel test
The 90-degree peel test is defined by several recognised international standards, which provide consistent methodology and reporting requirements:
1895
[Page extract]
Power and flexibility for your materials testing
Start measuring stress/strain, tensile, shear, flexure and compressive forces to evaluate your materials. It takes just a few minutes to create your own step-by-step test routines.
1896
[Page extract]
Step-by-step procedure for reverse ratchet torque testing
Sample preparation
Condition the closures according to the specified standard to control environmental factors.
1897
[Page extract]
Procedure for tensile testing
While the specifics vary depending on material type and applicable standards, the general procedure includes:
1898
[Page extract]
Why Mecmesin for climbing drum peel testing
Precision peel testing systems
Mecmesin offers test platforms such as the OmniTest and
1899
[Page extract]
Standards for yield point testing
Yield point testing protocols are defined by recognised international standards, including:
1900
[Page extract]
Simplify data analysis in force, materials and torque testing
Test calculations are the values derived from raw measurement data, such as peak force, torque angle, or modulus of elasticity. With advanced software, these are now calculated instantly and with high precision, replacing error-prone manual methods.