Search results
451
Accessory
Upper Precision Fixing Plate for Helixa sensors
432-601
Precision Upper Fixing Plate for Helixa.
Mounts onto the square-drive of Helixa torque sensors. Fitted with a precision leadscrew and sprung-loaded runners into which jaws or holding pegs can be inserted (order separately). Tighten the knob to secure…
452
Accessory
90-degree Peel Jig for FPT-H1
432-620
This 90-degree Peel Jig fits to the FPT-H1 for 90 degree peel testing of pressure sensitive tapes and labels in accordance with international standards.
FINAT FTM2, ASTM D330. PSTC 101 Method F.
It accepts interchangeable float glass and stainless steel…
453
[Page extract]
Introduction to compressibility and recovery testing
Compressibility and recovery testing measures how a material behaves under load and how effectively it returns to its original form once the load is removed.
454
Accessory
Rubber jaws for Mec240k Medium Vice Grip, 2.5 kN, 30 x 30 mm
Mec240k-BG
Rubber-faced Jaws (30mm x 30mm) - nickel-plated having 1mm thick layer of nitrile rubber coating.
Opening span = see datasheet for various spans according to the grip body selected.
For fragile samples, which may get weakened by pinching at the contact-…
455
[Page extract]
Standards and guidelines
Accurate and comparable cleavage strength testing depends on following recognised international standards.
456
Accessory
Diamond coated jaws for Mec240k Medium Vice Grip, 30 x 80 mm
Mec240k-BD80
Diamond Jaws (30mm x 80mm) - nickel-plated having clamping surface coated with synthetic diamonds.
Opening span = see datasheet for various spans according to the grip body selected.
For materials which need a “bite” to secure a good grip (e.g. soft…
457
[Page extract]
ASTM F2193-02
These specifications and test methods provide standard specifications that specify material, labeling, and handling requirements for components used in surgical fixation of the spinal skeletal system such as metallic spinal screws, spinal plates, and sp
458
Accessory
Charger for digital gauges, Europe, 230 V, 2-pin round
304-004
For use with Mecmesin digital force and torque gauges. 220 Volt with 2 round pins. Commonly used in Europe, South America and Asia.
The mains adaptor/charger is a constant-current type:
Primary circuit: 230V – 50Hz
Secondary circuit: 100mA constant…
459
Accessory
Plastic Carrying Case for AFTI, S-Beam loadcell, TS torque screwdriver and charger
416-049
A foam-lined plastic carry-case for the AFTI display.
Has space for:
AFTI display including rechargeable batteries,
mains adaptor / battery charger,
'Smart' S-beam Loadcell,
'Smart' TS Torque Screwdriver.
460
Accessory
Square Perforated Aluminium Compression Plate, 200 x 200 mm, QC-20 or QC-32 fitting
Mec36L-200-L6x20
MEC36L-200-L6x20
Square Compression Plate in aluminium featuring perforations to allow air release during testing - suitable for foam testing. Holes are 6mm diameter and spaced at 20mm intervals.
Dimensions: 200mm x 200mm.
Fitted with QC-20mm or 32mm…
461
Accessory
Dual Footswitches (locking type) for pneumatic grips
Mec205-2
Pneumatic grips are the ideal choice when performing tensile tests on sensitive materials that have a tendency to slip or break at point of clamping.
Mec 205-2:
Locking dual footswitches open the jaws of the grip by pressing the foot pedal and remain…
462
Accessory
1/2" upper chuck assembly for use on Helixa sensors (3 N.m & 6 N.m only)
432-617
A standard self-centering 3-jaw chuck with key.
It has a maximum ½" (12.7 mm) opening and is connected to the Helixa torque sensor via an adaptor with female ⅜" square hole.
Used to secure a variety of test specimens for torque applications of 1.5 - 10…
463
Accessory
Horizontal feet kit for 2.5 kN single-column test stand (on side)
PDV11065
Feet kit for the horizontal operation of a MultiTest motorised test.
When fitted the front panel of the test stand will be on its side for ease-of-operation by the user.
464
Accessory
Cable Cam grip for CrimpTest-1 kN
432-660
Cable Cam Grip for CrimpTest-1 Tester (supplied as standard with the Tester)
The Cable Cam Grip is designed for holding insulated cables and wire when tensile testing the pull strength of terminals up to 1 kN.
The cable is secured by the serrated cam,…
465
Accessory
Diamond coated jaws for Mec240k Medium Vice Grip, 30 x 80 mm
Mec240k-BD80
Diamond Jaws (30mm x 80mm) - nickel-plated having clamping surface coated with synthetic diamonds.
Opening span = see datasheet for various spans according to the grip body selected.
For materials which need a “bite” to secure a good grip (e.g. soft…
466
Accessory
Diamond coated jaws for Mec240k Medium Vice Grip, 30 x 50 mm
Mec240k-BD50
Diamond Jaws (30mm x 50mm) - nickel-plated having clamping surface coated with synthetic diamonds.
Opening span = see datasheet for various spans according to the grip body selected.
For materials which need a “bite” to secure a good grip (e.g. soft…
467
Case study
Medical suture device calibration system
Requirement
A number of devices which 'crimp' a curved needle to a fine medical thread needed to be tested. The crimp force was applied horizontally pulling a lever on the device.
468
Accessory
Square Perforated Aluminium Compression Plate, 150 x 150 mm, QC-20 or QC-32 fitting
Mec36L-150-L6x20
MEC36L-150-L6x20
Square Compression Plate in aluminium featuring perforations to allow air release during testing - suitable for foam testing. Holes are 6mm diameter and spaced at 20mm intervals.
Dimensions: 150mm x 150mm
Fitted with QC-20mm or 32mm…
469
Accessory
Dual Footswitches (non-locking type) for pneumatic grips
Mec205-1
Pneumatic grips are the ideal choice when performing tensile tests on sensitive materials that have a tendency to slip or break at point of clamping.
Mec205-1:
Non-locking dual footswitches open the jaws of the pneumatic grip by pressing the foot pedal…
470
Case study
Child safety - force to extract lighter
Requirement
The customer manufactures lighters and is currently developing a case/guard designed to increase the safety for children.
471
Case study
Metal bottle cap on glass pull-off test
Customised engineering example
Gripping the base of a glass bottle for a tensile test can be challenging due to the slippy surface and contoured shape.
472
Accessory
FPT COF sled 200g (foam) for ASTM D1894 and ISO 8295
432-638
A foam-faced sled with magnetic grips, for testing coefficient of friction of plastic film samples to ASTM D1894 and ISO 8295. Supplied with rigid and extensible links.
For use on the FPT-H1 Friction Tester.
473
Accessory
Diamond coated jaws for Mec240k Medium Vice Grip, 30 x 50 mm
Mec240k-BD50
Diamond Jaws (30mm x 50mm) - nickel-plated having clamping surface coated with synthetic diamonds.
Opening span = see datasheet for various spans according to the grip body selected.
For materials which need a “bite” to secure a good grip (e.g. soft…
474
Accessory
Diamond coated jaws for Mec240k Medium Vice Grip, 30 x 100 mm
Mec240k-BD100
Diamond Jaws (30mm x 100mm) - nickel-plated having clamping surface coated with synthetic diamonds.
Opening span = see datasheet for various spans according to the grip body selected.
For materials which need a “bite” to secure a good grip (e.g. soft…
475
Accessory
Digital Height Scale and Brackets for LCP/S Test Stand
432-162 V01
Digital Height Scale and Brackets for mounting to the lever-operated Manual Test Stand model LCP/S.
The digital display of the height-scale is fixed to the moving crosshead of the test stand so that it's displacement can be monitored. This is often…