Search results
2301
[Page extract]
ASTM C203
ASTM C203 is a test method that covers the determination of the breaking load and calculated flexural strength of a rectangular cross section of a preformed block-type thermal insulation tested as a simple beam.
2302
[Page extract]
ASTM D747-10
ASTM D747 is used to determine the flexibility of plastics by means of a cantilever beam.
2303
[Page extract]
ASTM D3810
This test method covers the determination of or the recommendation for minimum application torque that results in a fully degraded removal torque that is at a level greater than the maximum expected reverse-ratchet torque for a Type IA child-resistant c
2304
[Page extract]
ASTM C582
This specification covers composition, thickness, fabricating procedures, and physical property requirements for glass fiber reinforced thermoset polyester, vinyl ester, or other qualified thermosetting resin laminates comprising the materials of constr
2305
[Page extract]
BS EN 12814-3
BS EN 12814-3 is a tensile creep test method for testing welded joints of thermoplastics semi-finished products.
2306
[Page extract]
ASTM D5672-09
This test method covers a screening type quality control test used to determine if flexible polyurethane foam cushions are within the specified grade range for firmness.
2307
[Page extract]
ISO 9073-3
Application of a force longitudinally to a test piece of a specified length and width at a constant rate of extension. Determination of values for breaking strength and elongation from the recorded force-elongation curve.
2308
[Page extract]
Young's modulus
Measure how stiff or elastic a material is under tension or compression with Young’s modulus testing. Universal testing systems provide reliable modulus of elasticity measurements for compliance with global standards like ISO 527 and ASTM D638.
2309
[Page extract]
Baumann tear test
- slit cut laterally in the centre of sample; used to test the tear strength of leather
2310
[Page extract]
Ultimate Tensile Strength
What it is, how to measure it, and why it matters
Ultimate tensile strength (UTS) is a critical property used to determine how materials behave under tension. It defines the maximum stress a material can withstand before breaking.
2312
[Page extract]
Shear Modulus Guide
Understanding how a material behaves under sliding or twisting forces is essential when selecting the right component for mechanical or structural performance.
2313
[Page extract]
Elongation and Recovery
Elongation and recovery testing is a fundamental process in material science used to measure how far a material can stretch under a given load and how effectively it returns to its original shape once the force is removed.
2314
[Page extract]
Hospitals
Mecmesin provides force, materials and torque testing equipment for medical and dental hospitals and their associated teaching institutions.
2315
[Page extract]
Jewellery & Watch
In jewellery and watch production, alloys, components and other materials must meet the needs of the manufacturing process and the end-product should give good service performance when worn by the customer.
2316
Accessory
Extension Rod with thumbwheel, 30 mm, 5 kN, 5-16 UNC
432-008
30mm long Extension Rod 5-16 UNC female to 5-16 UNC male. Fitted with knurled thumbwheel for locking accessory in correct orientation.
2317
Accessory
QC Type K Adapter, 20 mm F to 5/16 UNC fixing bolt, c/w pin
432-429
QC Female Sleeve Type K c/w cross-pin with 5-16 UNC Fixing Bolt:
Converts a non-QC type grip having a 5-16 UNC fixing thread into a QC type thereby allowing for quick interchange of grips.
2318
Accessory
Interface cable, AFG/AFTI (2006 - now) or Tornado (2008 - now) to PLC
351-063
Connects AFG, AFTI or Tornado for data comms to a Programmable Logic Controller. Comprises 15-pin female D-connector to twin screened wires.
2319
Accessory
Mandrel Peg Drive, 54 mm
PDV15094-A
This fixture is connected to the torque sensor of the Vortex or Helixa. It has 4 metal pegs with an internal opening of 54 mm into which the single-form mandrel can be positioned. The pegs drive the mandrel and thereby apply the tightening and release…
2320
Accessory
Medium Vice Grip - Single Action, 1 kN, 30 mm opening, QC-20 fitting
Mec240k-S30
MEC 240k-S30 (body only) :
A Medium Single-action Vice Grip allowing one jaw to be set in a position to align a test specimen around the central axis. The other jaw is freely adjustable to mechanically clamp the specimen in place.
Rated to 1 kN in…
2321
Accessory
Extension Rod with thumbwheel, 30 mm, 500N, M6 to 10-32 UNF
432-007
Extension rod 30mm long having 10-32 UNF female to M6 male threads.
Fitted with knurled thumbwheel for locking accessory in correct orientation.
2322
Accessory
Diamond-coated Inset jaws, 0.5 set
Mec9-EBD
MEC9-EBD Diamond Jaws
Diamond-coated Inset jaws of 37 mm height x 15 mm width, 0.5 set. For fitting into the carrier of the MEC9 Thin Wire Grip.
Used when jaws need to bite into a soft material to clamp tightly and reduce the risk of slippage.(e.g. soft…
2323
Accessory
Trolley pushing fixture, 1 kN
432-405
The Trolley Pushing Fixture has been designed to attach to trolleys and wheelie bins, so that manual handling measurements can be made easily. Typically used with a force gauge grip handle.
2324
Accessory
Medium Vice Grip - Single Action, 1 kN, 30 mm opening, QC-20 fitting
Mec240k-S30
MEC 240k-S30 (body only) :
A Medium Single-action Vice Grip allowing one jaw to be set in a position to align a test specimen around the central axis. The other jaw is freely adjustable to mechanically clamp the specimen in place.
Rated to 1 kN in…
2325
Accessory
Interface cable, BFG (2003 - now), Orbis Mk1 (2003-2007), RS232
351-054
Connects the BFG or Orbis Mk1 to a PC for RS232 data comms.
15-pin male to 9-pin female D-connectors.