Search results
201
[Page extract]
BS EN 1394
BS EN 1394 is a tensile test method to determine the initial circumferential tensile strength of plastic pipes.
202
[Page extract]
BS EN ISO 22088-2
BS EN ISO 22088-2 is a test method for determining the environmental stress cracking of plastics.
This has replaced BS EN ISO 6252:1998
203
[Page extract]
ASTM D349
These test methods cover the procedures for testing rigid round rods used in electrical insulation.
204
[Page extract]
ASTM D3165
This test method is useful in that the joint configuration closely simulates the actual joint configuration of many bonded assemblies.
205
[Page extract]
ASTM D5083-17
ASTM D5083 is a test method for measuring the force required to break a reinforced thermoset plastic specimen and the extent to which the specimen stretches or elongates to that breaking point.
206
[Page extract]
ASTM D3846
ASTM D3486 is a test method used for evaluating the in-plane strength of reinforced thermosetting plastics in flat sheet form in thicknesses ranging from 2.54 to 6.60 mm.
207
[Page extract]
ASTM D6484 / D6484M - 14
ASTM D6484 is a test method that determines the open-hole compressive strength of multidirectional polymer matrix composite laminates reinforced by high-modulus fibers.
208
[Page extract]
ASTM C203
ASTM C203 is a test method that covers the determination of the breaking load and calculated flexural strength of a rectangular cross section of a preformed block-type thermal insulation tested as a simple beam.
209
[Page extract]
ASTM D952-15
ASTM D952 is a test method that covers the determination of the bond strength or ply adhesion strength of sheet plastic and electrical insulating materials.
210
[Page extract]
ASTM D3470
This test method covers the determination of the force required to cause a downward-force-while-turning lug-finish closure to be rotated across the container finish lugs (strippage) without downward force being applied to the closure (Type IIA closures)
211
[Page extract]
ASTM D5868-01
Due to the increased use of adhesively-bonded FRP as a result of the inherent advantages afforded by bonded rather than mechanically-fastened joints (particularly the alleviation of stress risers and stress cracking), there is a need for tests by which
212
[Page extract]
ISO 8113
ISO 8113 specifies a method for determination of the resistance of glass containers to external force in the direction of the vertical axis.
213
[Page extract]
ASTM D3474
This standard covers the calibration and use of torque meters of the type normally used in packaging applications.
214
[Page extract]
SAE J174M
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 6 through 24 mm nominal diameters.
215
[Page extract]
ASTM D2344 / D2344M
ASTM D2344 is a test method, which determines the short-beam strength of high-modulus fiber-reinforced composite materials. It is applicable to all types of parallel fiber reinforced plastics and composites.
216
[Page extract]
BS ISO 7743
ISO 7743 specifies methods for the determination of the compression stress-strain properties of vulcanized or thermoplastic rubber using a standard test piece, a product or a part of a product.
Four procedures are given:
217
[Page extract]
ASTM D378
The ASTM D378 test method is used for evaluating the physical properties of flat conveyor belting, which are used in many industrial applications in which they are subjected to a great variety of stresses and conditions.
218
[Page extract]
ASTM D6324-11
ASTM D6324 covers the minimum requirements for individually packaged male condoms made from polyurethane. This specification also describes the minimum inspection and quality levels that shall be utilized in referee tests.
219
[Page extract]
ASTM D2370
This test method covers the determination of the elongation, tensile strength, and stiffness (modulus of elasticity) of organic coatings when tested as free films.
220
[Page extract]
ISO 13954
ISO 13954 describes a peel test method for determining the decohesive resistance of polyethylene electrofusion socket assemblies for use in the distribution of fluids.
221
[Page extract]
ISBT PTC-00004
These ISBT (International Society of Beverage Technologists) Sport Closure test methods focus on child safety related parameters such as separation forces and choking hazards of closure components.
222
[Page extract]
ISO 252
ISO 252 specifies two test methods, A and B, for determining the adhesion strength between constitutive elements of a conveyor belt, i.e. between plies and between covers and carcass.
223
[Page extract]
ISO 604
ISO 604 specifies a method for determining the compressive properties of plastics in the form of standard test specimens when tested under defined conditions of pretreatment, temperature, humidity and testing machine speed.
224
[Page extract]
ISO 814
ISO 814 specifies a method for determining the adhesion strength of rubber-to-metal bonds where the rubber part is assembled between two parallel metal plates, using the adhesive system under investigation