Search results
2427
[Page extract]
Case Studies and Capability Publications
Discover how Mecmesin solutions make a difference in real-world applications. Our collection of case studies and capability statements showcases the wide range of industries we support and the tests we help perform every day.
2428
[Page extract]
What is the grab method?
The grab method is a tensile testing technique where only the centre of a fabric specimen is gripped during testing — typically using 100 mm × 150 mm test specimens with a 50 mm wide clamp
2429
[Page extract]
Speak to a Mecmesin engineer
Need help defining the right friction testing solution for your application? Our application engineers are available to advise on:
2430
[Page extract]
Comparison of relevant standards
Standard
Material types
Peel angle
Environment
2431
[Page extract]
Versatility
The Vortex torque tester has been designed for versatility. Its standard configuration is rated to 10 N.m (90 lbf.in) with space to accept specimens up to 275mm wide.
2432
[Page extract]
Speak to an expert
Need help selecting the right test method or equipment for your material? Mecmesin specialists are available to advise on setting up effective bulk analysis routines.
2433
[Page extract]
Why automate?
Automation transforms the way you approach quality control and testing, turning a time-consuming and labour-intensive process into a more efficient and cost-effective operation.
2434
[Page extract]
Overview of TerraFixing
TerraFixing is dedicated to combating climate change through affordable and scalable Direct Air Carbon Capture (DAC).
2435
[Page extract]
Speak to an expert
Speak to an expert at Mecmesin about your tear resistance testing requirements, from selecting the correct wing tear method to configuring equipment for
2436
[Page extract]
Best practice and future trends
Maintaining accuracy
Calibrate to ISO 6789 or Mecmesin protocols
Use in controlled environments
Validate with certified torque standards
2437
[Page extract]
Impact of environmental factors
Temperature and mechanical properties
Temperature can significantly affect tangent modulus:
2438
[Page extract]
Speak to an Expert
For specialist advice on four-point bend testing—including test setup, standard compliance, and equipment selection—contact Mecmesin’s technical support team.
2439
[Page extract]
Speak to an expert
Discuss your requirements with a Mecmesin specialist to identify the right tension testing solution for your product and process.
2440
[Page extract]
Accuracy and repeatability
Achieve a level of accuracy and repeatability that cannot be achieved by manual testers. Reduce your testing time and increase your throughput when performing batch tests.
2441
[Page extract]
Brushes
Brushes use synthetic or natural filaments to create bristles which are typically clamped to a handle via a ferrule.
2442
[Page extract]
Significance of connector extraction resistance
Extraction resistance is the connector’s ability to maintain a secure fit during use while still allowing disconnection when necessary. This is especially important where connectors are repeatedly mated and unmated, such as:
2443
[Page extract]
BS EN 1465
Specifies a method for determining the tensile lap-shear strength of bonded assemblies when tested on a standard specimen and under specified conditions of preparation and testing.
2444
[Page extract]
NF G30-102
La présente partie a pour objet de décrire une méthode de mesure directe de la pression de contention des garnitures élastiques telles que les bords-côtes de chaussettes, ceinturesde slips et de culottes, gaines et bas dits de confort, et plus généralem
2445
[Page extract]
ASTM D2718
These test methods determine the shear properties of structural panels associated with shear distortion of the planes parallel to the edge planes of the panels. Both shear strength and modulus of rigidity may be determined.
2446
[Page extract]
NF S86-604
This document defines the test methods for characterizing metallic watch straps and the corresponding requirements.
2447
Event
Makers Hackathon, June 16-18th 2022, Malmö, Sweden
Who should attend?
Quality Managers, design/product engineers and materials specialist.
What is the exhibition about?
2448
[Page extract]
BS EN 50289-3-16
Communication cables, Electric cables, Communication transmission lines, Mechanical testing, Tensile testing, Tensile strength, Performance testing
2449
[Page extract]
ASTM F607-03
The ASTM F607 test method provides a means of determining the degree to which gasket materials under compressive load adhere to metal surfaces. The test conditions described are indicative of those frequently encountered in gasket applications.