Search results
1951
[Page extract]
BS EN 681-1
This standard specifies requirements for materials used in vulcanized rubber seals for:
1) cold potable water supply (up to 50®C);
1952
[Page extract]
ISO 20502
SO 20502:2005 describes a method of testing ceramic coatings by scratching with a diamond stylus.
1953
[Page extract]
ASTM D1321
This test method covers the empirical estimation of the consistency of waxes derived from petroleum by measurement of the extent of penetration of a standard needle.
1955
[Page extract]
BS EN ISO 9000
ISO 9000 gives an overview of the fundamentals and concepts around quality management.
1956
[Page extract]
ISO 14126
ISO 14126 outlines procedures for determining the compressive properties of fibre-reinforced plastics composites in the in-plane direction. Two methods are detailed in the standard:
1957
[Page extract]
ISO 8364
ISO 8364:2007 specifies requirements and test methods for the binding mounting area and free space area, ski bindings and retention devices of alpine skis, in order to optimize the compatibility of the functional unit "ski binding - retention device - b
1958
[Page extract]
BS EN 1607
This European Standard specifies the equipment and procedures for determining the tensile strength of a product perpendicular to its faces. It is applicable to thermal insulating products.
1959
[Page extract]
ISO 604
ISO 604 specifies a method for determining the compressive properties of plastics in the form of standard test specimens when tested under defined conditions of pretreatment, temperature, humidity and testing machine speed.
1960
Event
Medical Device Testing: Needle sharpness and syringe actuation testing (with 21 CFR Part 11 compliance)
Hypodermic needles are tested to determine their efficacy in piercing elastomer closures on vials and how their design influences the ease of insertion into the patient's skin, influencing pain and skin trauma.
The smooth and consistent operat
1961
Event
Cap Closure and Removal Torque Testing
The primary objective for measuring and analyzing the torque characteristics of a container cap is to accurately determine not only the quality of the part or process, but also the root cause of a wide variety of defects.
1962
[Page extract]
BS 6319-6
BS 6319-6 is a test method for determining the modulus of elasticity in compression of resin and polymer/cement compositions for use in construction.
1963
Event
Fundamentals of Food Texture Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
1964
[Page extract]
ASTM D2659
ASTM D2659 determines the mechanical properties of blown thermoplastic containers under columnar crush conditions at a steady rate of compression. Any container, whether blown commercially or in the laboratory, may be used as the test specimen.
1965
[Page extract]
ISO 8510-1
Particularly suitable for use with less flexible adherends for which a 180 ° peel test is not suitable because the adherends crack, break or delaminate. A bonded assembly of two adherends is prepared using the adhesive under test.
1966
[Page extract]
BS EN ISO 16409
Describes performance criteria for manual interdental brushes with a round cross-section of the brush head and consisting of a wired stem with inserted filaents.
Of particular interest is the Stem Retention Force (sections 5.4 and 7.6)
1967
[Page extract]
ASTM F543-13
This specification provides requirements for materials, finish and marking, care and handling, and the acceptable dimensions and tolerances for metallic bone screws that are implanted into bone.
1968
[Page extract]
ASTM F628-12e3
This specification covers coextruded acrylonitrile-butadiene-styrene (ABS) plastic drain, waste, and vent pipes made to Schedule 40 iron pipe sizes (IPS) with concentric inner and outer solid ABS layers and a closed-cell cellular ABS core.
1969
[Page extract]
SAE J1525
This SAE Recommended Practice describes a lap shear test method for use in measuring the bonding characteristics of automotive-type adhesives for joining fiber reinforced plastics to themselves and to metals.
1970
[Page extract]
ASTM C1341
This test method covers the determination of flexural properties of continuous fiber-reinforced ceramic composites in the form of rectangular bars formed directly or cut from sheets, plates, or molded shapes.
1972
[Page extract]
ISO 9727-2
This part of ISO 9727 specifies a test method for:
⎯ measuring the mass of cylindrical cork stoppers ready for use or semi-worked, totally or partially made of agglomerated cork, and
1973
[Page extract]
ISO 7810
Stipulates test method as per ISO/IEC 10373-1 for determining the Peel Strength of cards.
1974
[Page extract]
BS EN ISO 11857
Textile floor coverings, Floor coverings, Sheet flooring, Mechanical testing, Textile testing, Textiles, Tensile testing, Test equipment, Test specimens, Testing conditions.
1975
[Page extract]
ASTM F2332-06
This specification covers annular ball bearings intended primarily for use in instrument and precision rotating components.