Search results
1101
[Page extract]
Industry-specific test standards
ISO 9895 - packaging materials
ISO 9895 specifies the method for determining the compressive strength of paper and b
1102
[Page extract]
Introduction to peel testing
Peel testing is a fundamental method in materials testing, used to evaluate the strength of adhesive bonds between two materials.
1103
[Page extract]
Torque testing standards
A range of recognised standards define the correct procedures for reverse ratchet torque testing, ensuring consistent and reliable results.
1104
[Page extract]
Step-by-step needle penetration testing process
Sample preparation
Specimens are cut to the required dimensions and conditioned to the specified environmental parameters such as temperature and humidity. Thickness and surface finish are controlled for consistency.
1105
[Page extract]
Secant modulus compared to other moduli
Different moduli are used to describe the stiffness of materials, each calculated at different points on the stress-strain curve:
1106
[Page extract]
Applications in industry
Engineering and manufacturing uses
Tangent modulus testing supports design validation and process control in sectors where materials operate near or beyond the elastic range, for example:
1107
[Page extract]
Applications across sectors
Texture testing in food manufacturing
Bread softness for freshness control, snack crispness for quality assurance, firmness in
1108
[Page extract]
Key material testing standards
To ensure accuracy and comparability, elongation at break and tensile strength measurements are performed according to recognised industry standards.
1109
[Page extract]
Introduction to the ring crush test
The ring crush test (RCT) is a key method for determining the edgewise compression strength of paper and paperboard.
1110
[Page extract]
Types of flexure tests
Different flexure testing setups are chosen based on the nature of the material, the required precision, and the industry standards being followed.
1111
[Page extract]
What is fastening torque
Fastening torque refers to the rotational force applied to tighten a fastener, typically measured in Newton-metres (N·m) or pound-force inches (lbf·in). The correct torque value ensures adequate clamping without overstressing components.
1112
[Page extract]
Types of compressive shear tests
Test configurations vary according to the material, application, and relevant industry standard.
1113
[Page extract]
How peel wheel tests are conducted
Specimen preparation – The bonded material is cut to defined dimensions, ensuring uniformity of size and adhesive application.
1114
[Page extract]
Relevant textile test standards
The strip method is defined in several national and international standards, each tailored to specific fabric types and performance requirements:
1115
[Page extract]
How to conduct a Concora crush test
Step-by-step procedure
Specimen preparation - Cut medium to the required size, typically 152.4 mm by 25.4 mm strips, ensuring clean edges.
1116
[Page extract]
Introduction to friction in material science
Friction is a critical factor in how materials behave under movement. It is the resistive force that occurs when two surfaces are in contact and attempt to slide against each other.
1117
[Page extract]
ISO 34-2 standards explained
ISO 34-2 specifies the Delft tear test procedure for vulcanised or thermoplastic rubber, ensuring testing is carried out under consisten
1118
[Page extract]
Standards and compliance
International standards ensure penetration and puncture testing is performed consistently for reliable and comparable results.
Key examples include:
1119
[Page extract]
Step-by-step test methodology
Preparation
Sample selection - Choose representative specimens, avoiding faults unless deliberately testing them.
Specimen cutting - Cut to standard dimensions with a central slit of specified
1120
[Page extract]
Tools (calibration related)
To maintain consistent performance and accuracy, tools must be checked regularly.
1121
[Page extract]
Interpreting breakaway test results
Understanding test outputs is as crucial as conducting the tests themselves.
Slip torque vs bridge torque
Slip torque reflects the resistance encountered before rotation begins—a measure of seal integrity and usability.
1122
[Page extract]
Standards and compliance
ASTM D2063 defines methods for determining application and r
1123
[Page extract]
Understanding ASTM D2718 standards
The ASTM D2718 standard sets out the procedures for conducting planar shear tests on structural panels using the
1124
[Page extract]
Understanding reverse ratchet torque
Reverse ratchet torque testing is an essential process for verifying the safety and reliability of child-resistant closures (CRCs).
1125
[Page extract]
Introduction to flexural testing
Flexural testing is a core method in materials science, used to evaluate how materials perform when subjected to bending stresses.