The TSCC is a semi-automated test system for checking the calibration of preset and adjustable torque-limiting screwdrivers, up to
With preprogrammed tests and one-touch operation the TSCC eliminates inconsistencies in results and repetitive strain injury for operators, which is often associated with manual testing.
Got a question about this system? Get in touch and speak to one of our Technical Sales Engineers now...
Speak to an expert
The ITC range of interchangeable torque sensors specially adapted for the Vortex test system. Plug and play for automatic calibration and available in 5 different capacities for all requirements, from 0 - 0.3 N.m (0 - 2.7 lbf.in) to 0 - 10 N.m ( 0 - 90 lbf.in).
ITC torque sensors
The ITC range of interchangeable torque sensors is specially adapted to the Vortex-i and -xt test systems.
They plug into the frame and their calibration characteristics are immediately recognised by the software of the tester without any input from the operator.
Each sensor is fitted with a ⅜" male square drive for connection to a range of fixing tables and chucks to hold your specimens.
To ensure that you have the optimum selection to meet all your torque testing needs, five different interchangeable sensors are available. All sensors measure from zero up to their nominal capacity allowing you to use the Vortex for low torque measurements up to 0.3 N.m and right up to 10 N.m.
Sensor capacity, range and accuracy
Each sensor reads from zero to its full nominal capacity (listed below). Measurement accuracy is an outstanding ±0.5% of the sensor capacity.
|Model||0.3 N.m||1.5 N.m||3 N.m||6 N.m||10 N.m|
|N.m||0 - 0.3||0 - 1.5||0 - 3.0||0 - 6||0 - 10|
|kgf.cm||0 - 3||0 - 15||0 - 30||0 - 60||0 - 100|
|lbf.in||0 - 2.7||0 - 13||0 - 26||0 - 52||0 - 90|
Each sensor is delivered as standard with its own calibration certificate traceable to national standards.
Servicing and calibration
Mecmesin also provides annual servicing and torque sensor re-calibration. Talk to one of our engineers or your local national distributor to find out more.
Torque screwdrivers are designed to eliminate under and over-tightening by slipping when applying a fixed torque. To ensure they perform correctly and reliably, they must be checked and calibrated regularly.
Manual methods of calibration are highly time-consuming and can be influenced by different operators. This makes it expensive to check large numbers of tools, as well as putting staff at risk of repetitive strain injuries.
The TSCC is based on Mecmesin’s Vortex-xt automated torque tester. Designed to eliminate the variability associated with manual calibration methods, this system uses the highest quality certified torque cells and a pre-set speed to guarantee optimum accuracy and repeatability.
A universal test fixture makes it easy to mount all sizes of torque screwdriver, ensuring consistency when checking different tool types.
With simple and intuitive operation controls, a torque test is completed at the push of a button - keeping operator training and testing time to a minimum.
Typically taking three torque measurements per tool in under thirty seconds, this torque screwdriver check calibrator provides instant pass/fail indication to the operator.
Adjusting the pre-set mechanism in the tool can be done on-the-spot and retested immediately.
A handy touch-screen console on the side of the machine stores all your pre-programmed tests and collects the data for export and reporting functions.
A barcode reader is even available for scanning tool ID’s which are automatically registered in the software of the tester for inclusion in test reports.
Available sensors (all measure from zero to the value indicated in the table below)
|Model ITC||0.3 N.m||1.5 N.m||3 N.m||6 N.m||10 N.m|
±0.5% of full scale
Units of measurement
mN.m, N.cm, N.m, kgf.cm, gf.cm, ozf.in, lbf.in, lbf.ft
0.1 - 20 rev/min (clockwise or counter-clockwise)
±1% of indicated speed
505 mm (19.9") without mounting tables
448 mm (17.6") with mounting tables fitted
Maximum travel of adjustable carriage
182 mm (7.2")
Width between columns
280 mm (11.02")
Opening span of lower mounting table
10 - 190 mm (0.39 - 7.5")
Opening span of upper mounting table
10 - 78 mm (0.39 - 3.07")
19.5 kg (43 lb)
Maximum power requirements
230 V AC 50 Hz or 110 V AC 60 hz
10 - 35°C (50 - 95°F)
Normal industry and laboratory conditions
Compensation for system movement
Online test equipment and training demos
As more people are working from home to reduce non-essential travel, our technical sales engineers can provide online equipment demos or training sessions via web-based video calls.
If possible, send in your own samples and our sales team will be able to present your own products being tested.
Get in touch to discuss your requirements and to arrange an online demo or training session.