Search results
1376
[Page extract]
ISO 9073-18
ISO 9073-18:2007 specifies a grab tensile test procedure for determining the breaking strength and elongation of most nonwoven materials. It includes instructions for the testing of wet specimens.
1377
[Page extract]
ASTM D1623
ASTM D1623 determines the tensile and tensile adhesion properties of rigid cellular plastics materials and foam. These are often used as insulation and structural materials in the aerospace, automotive and construction industries.
1378
[Page extract]
ASTM D6713-14
Materials shall be tested and the individual grades shall conform to specified values of the physical properties such as tensile strength, tensile elongation, tensile modulus, dimensional stability, flexural modulus, and Izod impact; and dimensional pro
1379
[Page extract]
ASTM D4476 / D4476M-14
ASTM D4476 is a test method used to determine the flexural properties of fiber-reinforced pultruded plastic rods. The specimen used is a rod with a semi-circular cross section, moulded or cut from lengths of pultruded rods.
1380
[Page extract]
ASTM D380
ASTM D380 is a set of test methods for determining testing and inspection procedures for rubber hoses e.g. hydraulic hoses and automotive hoses.
1381
[Page extract]
BS EN 12814-6
BS EN 12814-6 is a low temperature tensile test method for testing welded joints of thermoplastics semi-finished products.
1382
Case study
Car door closure effort
Requirement
When shutting car doors, users need to apply a certain force to initiate the movement and ensure a complete closure.
1383
[Page extract]
BS EN 50081-1
This standard for emission requirements applies to electrical and electronic apparatus intended for use in the residential, commercial and light-industrial environment, as described in clause 5, for which no dedicated product or product-family emission
1384
Event
Essentials of Adhesion (Peel) Testing
Across many households and industries, consumers have developed a strong preference for and confidence in ‘Duct Tape’ for all types of uses and applications. This is mainly due to the adhesion strength.
1385
Case study
Rượu có thể bật và xé lực mở
Yêu cầu Những người sành rượu truyền thống đã nhìn thấy một sự phát triển bao bì về cách đóng cửa; nút chai tự nhiên đến vật liệu nút chai tổng hợp để cuộn nắp vặn Tamper-Evident / Pilfer-Proof (ROTE / ROPP).
1386
[Page extract]
ISO 20344
This Standard specifies methods for testing footwear designed as personal protective equipment.
8 groups of tests from dimensions to mechanical properties and fluid resistance.
Supplemented by ISO 20345
1387
[Page extract]
ISO 11339
ISO 11339:2010 specifies a T‑peel test for the determination of the peel strength of an adhesive by measuring the peeling force of a T‑shaped bonded assembly of two flexible adherends. This test procedure does not provide design information.
1388
[Page extract]
ASTM D3916
ASTM D3916 is a test method for determining the tensile properties of pultruded, glass-fiber-reinforced thermosetting plastic rod of diameters ranging from 3.2 mm to 25.4 mm.
1389
[Page extract]
CETIE Guide 4
This document concerns the crowning process, using crown caps for which the seal is provided by a plastic liner, onto glass finishes adapted to either "pry-off" or "twist crown" applications.
1390
Case study
Seat belt locking device test
Requirement
The customer requested a system to measure the force required to release the locking mechanism of a car seat-belt whilst it is under tension.
1391
[Page extract]
BS EN ISO 8295
ISO 8295 specifies a method for determining the coefficients of starting and sliding friction of plastics film and sheeting when sliding over the same or other substances. It is intended to be used for non-sticky plastic film and sheeting of up to appr
1392
[Page extract]
ASTM D76-99
This specification covers operating characteristics of tensile testing machines for the determination of the force-elongation properties of textile materials.
1393
Page
Contact service
Need calibration or servicing support?
Whether it’s a Mecmesin product or another brand, our team can help. Complete the form below and one of our Service Engineers will get back to you.
1394
[Page extract]
ASTM D7834-13
During the application of coatings, paint brushes can exhibit shedding of filling material onto the coated surface. A measure of this shedding filling material will determine the paint brush’s ability to resist shedding during application.
1395
[Page extract]
ASTM D1414
ASTM D1414 is used to measure the mechanical properties of vulcanized rubber o-rings. Mecmesin test equipment is relevant to the tensile testing part of this standard, which covers a variety of different tests.
1396
[Page extract]
ASTM D2344 / D2344M
ASTM D2344 is a test method, which determines the short-beam strength of high-modulus fiber-reinforced composite materials. It is applicable to all types of parallel fiber reinforced plastics and composites.
1397
[Page extract]
ASTM E1820-18ae1
The ASTM E1820 test method covers procedures and guidelines for the determination of fracture toughness of metallic materials using the following parameters: K, J, and CTOD (δ). Toughness can be measured in the R-curve format or as a point value.
1398
[Page extract]
ISO 527-5
ISO 527-5 specifies the test conditions for the determination of the tensile properties of unidirectional fibre-reinforced plastic composites, based upon the general principles given in ISO 527-1.
1399
[Page extract]
ASTM D378
The ASTM D378 test method is used for evaluating the physical properties of flat conveyor belting, which are used in many industrial applications in which they are subjected to a great variety of stresses and conditions.
1400
Event
Automotive Component Torque Testing
This webinar will focus on the measurement of the torque resistance in knobs, switches, and torsion springs, which are among several components in automobiles that require testing to ensure quality, performance, and safety.