Search results
2226
[Page extract]
ASTM C1147
ASTM C1147 testing covers the evaluation of joints between two pieces of weldable grades of thermoplastic material. This testing is intended to establish methods to evaluate minimum short term weld factors.
2227
[Page extract]
ASTM D2633
ASTM D2633 test methods cover procedures for the testing of thermoplastic insulations and jackets used on insulated wire and cable.
2228
[Page extract]
AEC Q200-005
This specification establishes the procedure and criteria to determine the ability of surface
mounted device terminations and seals to withstand bending, flexing and pulling forces which
2229
[Page extract]
BS EN 12814-1
BS EN 12814-1 is a bend test method for testing welded joints of thermoplastics semi-finished products.
2230
[Page extract]
TAPPI T 556
This procedure is used to measure the bending resistance of paper and paperboard in the machine and cross machine directions, by determining the bending resistance in mN of a 38mm (1.5in) wide vertically clamped sample, at 15o or 7.5o deflection.
2231
[Page extract]
ASTM D1709-03
These test methods cover the determination of the energy that causes plastic film to fail under specified conditions of impact of a free-falling dart.
2232
[Page extract]
BS EN ISO 1856
BS EN ISO 1856 is a test method that specifies three methods for determining the compression set of flexible cellular materials and applies only to latex and polyurethane foams of thickness greater than 2 mm.
2233
[Page extract]
ASTM D7084-04
1.1 This test method covers the determination of bulk crush strength of a bed of formed catalyst particles 1⁄32 to 3⁄16 in.
2234
[Page extract]
ISO 15359
This International Standard specifies, a friction-testing method based on the horizontal plane principle, and the procedure for the determination of the static coefficient of friction before, and static and kinetic coefficients of friction after, a spec
2235
[Page extract]
Compression
Compression tests are performed to evaluate the performance of a material or component under gradually increasing compressive load.
2236
[Page extract]
ASTM D575-91
These test methods cover two test procedures for determining the compression-deflection characteristics of rubber compounds other than those usually classified as hard rubber and sponge rubber.
2237
[Page extract]
IFI 543
This standard provides a test method for determining the torque-tension relationship on both external and internal threaded fasteners for the purpose of measuring the frictional characteristics of the threaded fasteners.
2238
[Page extract]
MIL AS23190A
AS23190 is a procurement specification that covers a series of plastic and metal components and devices used for the tying, positioning, and supporting cable, cable assemblies, wire, and wire bundles in electrical, electronic and communication equipment
2239
[Page extract]
ASTM C674
These test methods cover determination of the modulus of rupture and the modulus of elasticity of fired ceramic whitewares bodies, formed by any fabrication method, and are applicable to both glazed and unglazed test specimens.
2240
[Page extract]
BS EN 2591-418
Describes a method of determining the insertion/extraction forces of female contacts used in elements of electrical and optical connection by means of gauges.
2241
[Page extract]
ASTM F2592
1.1 This test method covers the measurement of force displacement characteristics of a membrane switch.
2242
[Page extract]
ASTM F607-03
The ASTM F607 test method provides a means of determining the degree to which gasket materials under compressive load adhere to metal surfaces. The test conditions described are indicative of those frequently encountered in gasket applications.
2243
[Page extract]
BS EN 17665
The Directive (EU) 2019/904 “on the reduction of the impact of certain plastic products on the environment” introduces the requirement that plastic caps and lids of single use plastic beverage containers up to 3 l capacity shall remain attached to the c
2244
Case study
Peel testing Ostomy bags
Requirement
Salts Healthcare, a leading manufacturer and supplier of health care products required a low capacity system for testing the integrity of their hydrocolloid products.
2245
[Page extract]
ISO 10354
Simulates in a qualitative manner the forces and effects on an adhesive-bonded joint at a metal-adhesive/primer interface. It can also be used as a method of checking the surface preparation of substrates.
2246
[Page extract]
ISO 7622-2
ISO 7622-2 specifies a method for the determination of the tensile strength, in the longitudinal, of steel cords constituting the carcass of conveyor belts.
It applies exclusively to conveyor belts with a steel carcass.
2247
[Page extract]
TAPPI T 826
This method describes a procedure for determining the compressive resistance of containerboard. This method is intended for containerboard having a span-to-thickness ratio of 5 or less.
2248
[Page extract]
Consumer Products
Mecmesin test solutions for products typically found in the home ...
2249
[Page extract]
BS 6079-1
BS 6079-1 aims to help people and organizations achieve a desired outcome of a project efficiently and effectively, as well as to contribute to the learning within projects and so continually improve their organization’s project management capability.
2250
[Page extract]
BS EN ISO 14129
BS EN ISO 14129 is a test method used to determine the in-plane shear stress/shear strain response of fibre-reinforced plastic components.