Search results
1176
Product
Máy đo lực vặn nắp chai
Orbis
876-107
Máy kiểm tra mô-men xoắn kỹ thuật số Orbis phù hợp lý tưởng cho các bài kiểm tra mô-men xoắn theo chiều kim đồng hồ và ngược chiều kim đồng hồ cơ bản.
Được vận hành bằng tay và đo được công suất lên đến 6 Nm , công suất của nó là lý tưởng cho hầu hết các…
1177
Product
Máy kiểm tra vật liệu hai cột
OmniTest
Máy kiểm tra vật liệu đa năng và dễ sử dụng, OmniTest cột đôi có sẵn ở các công suất 10 kN, 25 kN và 50 kN . Được điều khiển bởi VectorPro MT, phần mềm kiểm tra vật liệu mới được phát triển của Mecmesin được thiết kế để sử dụng trong các phòng thí nghiệm…
1178
Product
Máy kiểm tra vật liệu một cột
OmniTest
Máy kiểm tra vật liệu đa năng và dễ sử dụng, OmniTest một cột có sẵn ở công suất 5 kN và 7,5 kN . Được điều khiển bởi VectorPro MT, phần mềm kiểm tra vật liệu mới được phát triển của Mecmesin được thiết kế để sử dụng trong các phòng thí nghiệm QC và R…
1179
[Page extract]
ISO 29862
This test standard specifies a series of methods for the determination of peel adhesion properties of self adhesives tapes.
1180
[Page extract]
ISO 1924-1
Applies, within the limitations of the instruments used, to all papers and boards with the exception of corrugated board, but may be applied to the components of such board. Specifies the method which causes failure of the piece in a mean time of 20 s.
1181
[Page extract]
ASTM E328-02
These test methods cover the determination of the time dependence of stress (stress relaxation) in materials and structures under conditions of approximately constant constraint, constant environment, and negligible vibration.
1182
[Page extract]
BS EN ISO 376
BS EN ISO 376:2011 looks at the calibration of force-proving instruments used for the static verification of uniaxial testing equipment. These include tension and compression testing machines.
1183
[Page extract]
ASTM D953-18
ASTM D953 is a test method that covers the determination of the pin-bearing strength of rigid plastics in either sheet form, molded form, or in reinforced thermoset form.
1184
[Page extract]
BS ISO 3597-2
ISO 3597-2 specifies a method for determining the flexural strength of composite rods of circular cross-section made of roving-reinforced resin.
1185
[Page extract]
ANSI/EIA 364-38B
This standard establishes a test method to determine the axial tensile load that can be applied to a mated pair of connectors and the holding effect of a connector cable clamp without causing any detrimental effects upon the cable or connector when subj
1186
[Page extract]
BS EN 1492-1
Specifies the requirements related to safety, including methods of rating and testing single-, two-, three-, four-leg and endless sewn flat woven webbing slings, with or without fittings, made of polyamide, polyester and polypropylene man-made fibre web
1187
[Page extract]
ASTM D3167
ASTM D3167 is used to determine the average peel strength or force of an adhesive and bonding agents through the use of floating roller fixtures. This is used to compare adhesives or to compare adhesive surface preparation procedures.
1188
[Page extract]
BS EN ISO 527-2
ISO 527-2 specifies the test conditions for determining the tensile properties of moulding and extrusion plastics, based upon the general principles given in ISO 527-1.
1189
[Page extract]
ISO 14126
ISO 14126 outlines procedures for determining the compressive properties of fibre-reinforced plastics composites in the in-plane direction. Two methods are detailed in the standard:
1190
[Page extract]
ISO 7810
Stipulates test method as per ISO/IEC 10373-1 for determining the Peel Strength of cards.
1191
[Page extract]
ISO 1966
Describes the design requirements and tests for the crimping of insulated and non-insulated terminations to general purpose cables, with conductors of copper, copper alloy, aluminium or aluminium alloy, in locations in which the stabilized conductor tem
1193
[Page extract]
BS EN ISO 80369-20
These standards describes the methods for testing the performance of 6% Luer lock fittings including assembly, leak tightness, stress cracking, and separation force.
1194
Event
Compression Testing in Top Load Applications
A typical challenge in packaging, and bottling applications is trying to balance product integrity, where the container might be too weak and crush under load, and excessive raw material cost, where the container is too strong.
1195
[Page extract]
ASTM D2979
This test method covers measurement of the pressure-sensitive tack of adhesives.
1196
[Page extract]
ASTM D6958-03
These test methods describe an evaluation procedure for the determination of undesirable side-bonding of coatings for wood flooring.
1197
Event
WestPack Expo 2025
Lansmont - together with our sister brand Mecmesin - will be participating in the upcoming WestPack trade show!
1198
[Page extract]
ISO 11897
ISO 11897 specifies a method for the determination, under given conditions, of the resistance to tear propagation on an edge fold of sacks made from thermoplastic flexible film.
1199
[Page extract]
ASTM D412-16
ASTM D412 is a test standard for testing the tensile stress-strain properties of thermoset rubbers and thermoplastic elastomers. The standard is divided into two test methods.
1200
Sensor
Sensors - Helixa
Torque sensors
The HTC range of interchangeable torque sensors are specially adapted for the Helixa test system. Plug and play for automatic calibration with availability to suit all requirements in capacities from 0.1 N.m (0.9 lbf.in) to 6 N.m (50 lbf.in…