Search results
1251
[Page extract]
When High Ultimate Tensile Strength is a Disadvantage
While high UTS materials are strong, they can also be brittle and less ductile.
1252
[Page extract]
ASTM D6641 / D6641M - 16e1
The ASTM D6641 test method determines compressive properties of polymer composite materials by applying combined end-loading and shear-loading using a combined loading compression (CLC) fixture.
1253
[Page extract]
Why is double lap shear testing important?
The double lap shear test is widely used to determine the performance of adhesives in structural and semi-structural applications. It allows engineers to:
1254
[Page extract]
ISO 7623
ISO 7623 specifies a method for determining the bond strength of metal cords to their surrounding coating, either in the initial state or after thermal treatment.
1255
[Page extract]
ASTM D3577
1. Scope ... 1.1 This specification describes certain requirements for packaged sterile rubber surgical gloves used in conducting surgical procedures.
1256
[Page extract]
ASTM D4482-11
ASTM D4482 is a test method used to determine the fatigue life of rubber compounds undergoing a tensile-strain cycle. During part of the cycle, the strain is relaxed to a zero value.
1257
[Page extract]
Manual test stands
Manual test stands allow simple force testing when budgets are limited.
Lever-operated models enable rapid testing of tension and compression up to 500 N.
1258
[Page extract]
ASTM D229
ASTM D229 is a test method, which provides useful engineering information for evaluating the mechanical behaviour of rigid electrical insulation at elevated temperature.
1259
[Page extract]
Methods and applications
Common test methods
Most single lap shear tests are carried out under tensile loading, but the method can vary depending on material type, bond configuration and industry require
1260
[Page extract]
BS EN 60794-1-21:2015+A1
This part of IEC 60794 applies to optical fibre cables for use with telecommunication equipment and devices employing similar techniques, and to cables having a combination of both optical fibres and electrical conductors.
1261
[Page extract]
FINAT FTM2
This test method differs from FTM 1 in that it can allow the end user to compare the repositionability of different laminates.
1262
[Page extract]
Understanding cone penetration testing
Cone penetration testing is a precision method used to determine a material's resistance to penetration by a standardised cone-shaped probe under specific force conditions.
1263
[Page extract]
Introduction to friction in material science
Friction is a critical factor in how materials behave under movement. It is the resistive force that occurs when two surfaces are in contact and attempt to slide against each other.
1264
[Page extract]
ASTM D790-17
ASTM D790 is used to determine the flexural properties of unreinforced and reinforced plastics, including high modulus composites and electrical insulating materials utilizing a three-point loading system to apply a load to a simply supported beam (spec
1265
[Page extract]
Introduction to tear testing
Tear testing is a quality control procedure used to measure the resistance of a material to tearing under controlled conditions.
1266
[Page extract]
Introduction to ball burst strength testing
Ball burst testing measures the resistance of a material to rupture under localised force using a hemispherical probe.
1267
Case study
Thử nghiệm điện từ
Yêu cầu Parmeko là một nhà thiết kế và nhà sản xuất có trụ sở tại Leicester, các loại đế cắm theo tỷ lệ, các loại đế rời và nam châm giữ được sử dụng trong các ứng dụng năng lượng chất lỏng di động và công nghiệp, cũng như một loạt các chất lỏn
1268
[Page extract]
ASTM D3474
This standard covers the calibration and use of torque meters of the type normally used in packaging applications.
1269
[Page extract]
Application of standards in puncture testing
Standardised methods ensure test consistency and reliability across laboratories and production sites.
1270
[Page extract]
Standards and guidelines for torque testing
Overview of ASTM and CETIE standards
Standardised testing ensures consistency and compliance. Commonly followed guidelines include:
1271
[Page extract]
ISO 20502
SO 20502:2005 describes a method of testing ceramic coatings by scratching with a diamond stylus.
1272
[Page extract]
Introduction to peel wheel testing
The peel wheel test is a specialised adhesion test method used to measure the strength of adhesive bonds in flexible materials such as plastics, films, and laminates.
1273
[Page extract]
Why Mecmesin for bulk analysis
Expert engineering and equipment
Mecmesin systems are designed for precision and reliability in bulk testing applications.
1274
[Page extract]
ASTM D5748-95
This test method determines the resistance of a stretch wrap film to the penetration of a probe at a standard low rate, a single test velocity.