Search results
2551
[Page extract]
ISO 3035
This International Standard specifies a method for the determination of the flat crush resistance of corrugated fibreboard used in the manufacture of packing cases.
2552
[Page extract]
ASTM D3474
This standard covers the calibration and use of torque meters of the type normally used in packaging applications.
2553
[Page extract]
TAPPI T 839
This method describes procedures for determining the edgewise compressive strenght, with flutes vertical, loading perpendicular to the axis of the flutes, of a short column of single, double, or triple-wall corrugated fiberboard.
2554
[Page extract]
TAPPI T 809
This method describes a procedure for measuring the crushing resistance of a laboratory fluted strip of corrugating medium and provides a means of estimating, in the laboratory, the potential flat crush resistance of a corrugated board.
2555
[Page extract]
ASTM D926-17
ASTM D926 is a test method that covers the determination of plasticity and recovery of unvulcanized rubber by means of the parallel plate plastometer. Uncompounded, compounded, and reclaim rubber may be tested.
2556
[Page extract]
EN 12089
Thermal insulating materials, Bend testing, Construction materials, Loading, Deflection tests, Mechanical testing, Testing conditions, Test equipment, Test specimens, Reports, Accuracy, Reproducibility.
2557
[Page extract]
ASTM D1600
ASTM D1600 is a source of reference for definitions of abbreviated technical terms used in the plastics industry
Standards can be obtained from appropriate standard authorities.
2558
[Page extract]
BS EN 1394
BS EN 1394 is a tensile test method to determine the initial circumferential tensile strength of plastic pipes.
2559
[Page extract]
ASTM D5934-02
ASTM D5934 specifies the use of controlled rate of loading mechanical instrumentation on rectangular plastic bars molded directly or cut from sheets, plates, or molded shapes via three-point loading bending techniques to obtain material properties such
2560
[Page extract]
BS EN ISO 22254
ISO 22254:2005 specifies a test method for determining the resistance of the tufted portion of manual toothbrushes to deflection. This could be used to derive a stiffness - a factor which has been of great concern to consumers and manufacturers.
2561
[Page extract]
BS EN ISO 10590
This International Standard specifies a method for the determination of the influence of water immersion on the adhesion/cohesion properties at maintained extension of sealants used in joints in building construction.
2562
[Page extract]
USP 1207.3
USP 1207.3 provides guidance on the integrity assurance of nonporous packages intended for sterile pharmaceutical products. Background instruction is provided on the topics of leaks, leakage rate, and package sealing/closure mechanisms
2563
Event
Tensile Testing: Basics, Tips and Trends
Have you ever wondered if the seatbelt in your vehicle is strong enough to restrain you in a collision? How about the average person pulling the cork out of a wine bottle?
2564
Event
Materials Testing: Theory and Practice Pt. 2
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
2565
Specials
Vector instruments - Intuitive touchscreens
Intuitive touchscreen
The most advanced touchscreen force and torque gauges, powered by Vector OS.
Handheld instruments built for tough environments to deliver accuracy and reliability.
2566
[Page extract]
ASTM D1621
ASTM D1621 is used to measure the compressive properties of rigid cellular materials, particularly expanded plastics. Calculations include compressive strength, compressive strain, compressive stress and compressive modulus.
2567
Event
Wine & Spirits Capping: Cork Pull & Twist Caps
Wine packaging has a great influence on the quality of the product delivered to the customer.
2568
[Page extract]
ASTM D3822
This test method covers the measurement of tensile properties of natural and man-made single textile fibers of sufficient length to permit mounting test specimens in a tensile testing machine.
2569
[Page extract]
BS EN 1465
Specifies a method for determining the tensile lap-shear strength of bonded assemblies when tested on a standard specimen and under specified conditions of preparation and testing.
2570
[Page extract]
NF G30-102
La présente partie a pour objet de décrire une méthode de mesure directe de la pression de contention des garnitures élastiques telles que les bords-côtes de chaussettes, ceinturesde slips et de culottes, gaines et bas dits de confort, et plus généralem
2571
Event
Materials Testing: Theory and Practice Pt. 2
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
2572
[Page extract]
ASTM D3518 / D3518M
ASTM D3518 is a test method, which measure the shear stress and shear strain properties of polymer matrix composite materials composed of +45 plies and -45° plies.
2573
[Page extract]
ASTM C674
These test methods cover determination of the modulus of rupture and the modulus of elasticity of fired ceramic whitewares bodies, formed by any fabrication method, and are applicable to both glazed and unglazed test specimens.
2574
[Page extract]
BS EN 50289-3-16
Communication cables, Electric cables, Communication transmission lines, Mechanical testing, Tensile testing, Tensile strength, Performance testing
2575
[Page extract]
ASTM D1623
ASTM D1623 determines the tensile and tensile adhesion properties of rigid cellular plastics materials and foam. These are often used as insulation and structural materials in the aerospace, automotive and construction industries.