Search results
2501
Specials
Thermal cabinet environment chamber
Environmental chamber capability
Mecmesin's OmniTest twin column range can accommodate an environmental chamber to test materials in controlled ambient conditions.
2502
[Page extract]
AEC Q200-005
This specification establishes the procedure and criteria to determine the ability of surface
mounted device terminations and seals to withstand bending, flexing and pulling forces which
2503
[Page extract]
ASTM E8/E8M-13a
These test methods cover the tension testing of metallic materials in any form at room temperature, specifically, the methods of determination of yield strength, yield point elongation, tensile strength, elongation, and reduction of area.
2504
[Page extract]
BS EN 319
EN319 specifies a method for determining the resistance to tension perpendicular to the plane of the board (“internal bond”) of particleboards, fibreboards, and cement-bonded particleboards.
2505
[Page extract]
BS EN ISO 6892-1
This part of ISO 6892 specifies the method for tensile testing of metallic materials and defines the mechanical properties which can be determined at room temperature.
2506
[Page extract]
TAPPI T 549
This method describes a horizontal plane procedure for the determination of the coefficient of static and kinetic friction of paper measured when sliding against itself.
2507
[Page extract]
BS 1726-3
Springs, Helical springs, Cylindrical shape, Torque, Circular shape, Wires, Bars (materials), Parallel, Dimensional tolerances, Form tolerances, Product specification, Ordering, Mechanical testing, Heat treatment
2509
[Page extract]
ASTM D1894
This test method is used to measure the friction of plastic film and sheeting. It determines the kinetic (moving) and static (starting) resistance of one surface being dragged across another.
2510
[Page extract]
ASTM C158
These test methods cover the determination of the modulus of rupture in bending of glass and glass-ceramics. These test methods are applicable to annealed and prestressed glasses and glass-ceramics available in varied forms.
2511
[Page extract]
BS EN 843-1
EN843-1 describes methods for determining the nominal flexural strength of advanced monolithic technical ceramic materials at ambient temperature.
2512
Event
Tensile Testing: Basics, Tips, & Trends
Have you ever wondered if the seatbelt in your vehicle is strong enough to restrain you in a collision? How about the average person pulling the cork out of a wine bottle?
2513
[Page extract]
ISO 13445
Specifies a method for the determination of the shear strength of adhesives used to bond materials with elastic moduli higher than the elastic modulus of the adhesive.
2514
[Page extract]
BS 4839
Specification for Blow moulded polyolefin containers, part 2: Plastics containers. Containers over 5 litres and up to 60 litres capacity
2515
[Page extract]
ASTM D3658
This test method covers the simplistic comparison of strengths of glass/metal joints when the adhesive is cured by ultraviolet (UV) radiation and standard specimens are used and tested under specified conditions of preparation, radiation, and load.
2516
[Page extract]
ISO 2409
Describes a test method for assessing the resistance of paint coatings to separation from substrates when a right-angle lattice pattern is cut into the coating, penetrating through to the substrate.
2517
[Page extract]
ASTM C1028
This test method covers the measurement of static coefficient of friction of ceramic tile or other surfaces under both wet and dry conditions while utilizing Neolite heel assemblies. This test method can be used in the laboratory or in the field.
2518
[Page extract]
ISO 7263
Specifies two methods for the determination of the flat crush resistance of a corrugating medium after laboratory fluting.
2519
[Page extract]
*corp QPF-MC-1209 B
*Strictly confidential*
L'Oreal to methods for shear and penetration testing of lipsticks, deodorants etc.
2520
[Page extract]
TAPPI T 576
This test method decribes the procedure, using constant-rate-of-elongation, for determining three tensile breaking properties of towel and tissue: tensile strength, stretch, and tensi;e energy absorption.
2521
[Page extract]
ASTM D952-15
ASTM D952 is a test method that covers the determination of the bond strength or ply adhesion strength of sheet plastic and electrical insulating materials.
2522
[Page extract]
BS EN 12467
Sheet materials, Asbestos cement, Cements, Fibres, Reinforced materials, Sheet roof coverings, Cladding (buildings), Curtain walling, Grades (quality), Density, Strength of materials, Approval testing, Type testing, Quality control, Acceptance inspectio
2523
[Page extract]
TAPPI T 841
This method describes procedures for determining the edgewise compressive strength, parallel to the flutes, of a short column of single wall and double wall corrugated fiberboard.
2524
[Page extract]
ASTM D5169-98
This test method measures the shear strength of hook and loop touch fasteners using a recording constant rate of extension (CRE) tensile testing machine.
2525
[Page extract]
IEC 62137-1-1
The test method described in IEC 62137-1-1:2007 is applicable to gull-wing lead surface mounting components.