Search results
1876
[Page extract]
Architectural
Force and torque testing within the architectural industry primarily involve the testing of architectural hardware and access control systems, to ensure operational forces are within the limits stipulated by various guidelines and test standards, eg&nbs
1877
Test Frame
Helixa test frame
Helixa test frame
A precision motorised test frame designed to apply torque from a few mN.m right up to a capacity of 6 N.m. (50 lbf.in).Its sensitivity and axial alignment make it perfectly suited for testing fine-precision components in a quality…
1878
Sensor
Sensors - Vortex
Torque sensors (ITC)
The ITC range of interchangeable torque sensors is specially adapted for the Vortex-i and -xt test systems. Plug and play for automatic calibration and available in 5 different capacities for all requirements, from 0 - 0.3 N.m (0 - 2.…
1879
[Page extract]
Power and flexibility for your materials testing
Start measuring stress/strain, tensile, shear, flexure and compressive forces to evaluate your materials. It takes just a few minutes to create your own step-by-step test routines.
1880
[Page extract]
Why Mecmesin for climbing drum peel testing
Precision peel testing systems
Mecmesin offers test platforms such as the OmniTest and
1881
[Page extract]
Applications across industries
Aerospace - testing honeycomb panels for aircraft interiors and structural assemblies.
Automotive<
1882
[Page extract]
Live performance and realtime results
See exactly how your test specimen is performing with realtime results on a live graph, with data captured at 500 times a second (500 Hz).
1883
[Page extract]
Applications across industries
Mecmesin torque to turn systems are used in sectors including:
1884
[Page extract]
Standards for the 90-degree peel test
The 90-degree peel test is defined by several recognised international standards, which provide consistent methodology and reporting requirements:
1885
[Page extract]
Simplify data analysis in force, materials and torque testing
Test calculations are the values derived from raw measurement data, such as peak force, torque angle, or modulus of elasticity. With advanced software, these are now calculated instantly and with high precision, replacing error-prone manual methods.
1886
[Page extract]
Built for batch testing and automation
Batch testing in VectorPro uses a pre-configured test to create a semi-automatic or fully automatic testing system on sets of products and batches of the products.
1887
[Page extract]
Step-by-step procedure for reverse ratchet torque testing
Sample preparation
Condition the closures according to the specified standard to control environmental factors.
1888
[Page extract]
Energy
Mecmesin has long been providing force and torque testing solutions to suppliers and contractors into the energy industry...
1889
[Page extract]
Jewellery & Watch
In jewellery and watch production, alloys, components and other materials must meet the needs of the manufacturing process and the end-product should give good service performance when worn by the customer.
1890
Case study
Thử nghiệm xoay mũ thể thao ISBT
Yêu cầu Hiệp hội các nhà công nghệ đồ uống quốc tế (ISBT) công bố các quy tắc hành nghề tự nguyện cho các khía cạnh kỹ thuật và khoa học của nước giải khát và đồ uống.
1891
[Page extract]
ISO 1798
ISO 1798 specifies a method for determining the strength and deformation properties of flexible cellular materials when a test piece is extended at a constant rate until it breaks.
This test standard is equivalent to BS EN ISO 1798:2008
1892
[Page extract]
ISO 36
ISO 36 determines the strength required to separate two plies of fabric bonded together with rubber, or a rubber and a fabric ply bonded together. This test is referred to as a “T-peel” test, because as the two adherends are pulled apart, they form the
1893
Event
Wire Crimp & Weld Testing Webinar
The only way of really knowing the strength of a crimped terminal is to pull it.
1894
[Page extract]
BS EN 12311-2
BS EN 12311-2 is a test method for determining the tensile properties of flexible sheets used for waterproofing roofs.
1895
[Page extract]
BS EN 1393
BS EN 1393 specifies a test method for testing the longitudinal tensile properties of glass-reinforced thermosetting plastics (GRP) pipes.
1896
[Page extract]
ASTM D2659
ASTM D2659 determines the mechanical properties of blown thermoplastic containers under columnar crush conditions at a steady rate of compression. Any container, whether blown commercially or in the laboratory, may be used as the test specimen.
1897
[Page extract]
BS EN 671-2
Fire hydrants, Fire hoses, Firefighting equipment, Flexible pipes, Fire safety in buildings, Design, Performance, Performance testing, Conformity, Approval testing, Corrosion tests, Ageing tests, Flow measurement, Impact testing, Pressure testing, Hydra
1898
[Page extract]
PSTC 101
These methods cover the measurement of the peel adhesion of pressure sensitive tapes.
1899
[Page extract]
ASTM D413-98
ASTM D413 is a test method used to determine the force per unit width required to separate a rubber layer from a flexible substrate such as fabric, wire or sheet metal.