Search results
1001
[Page extract]
PSTC 131
SCOPE
1.1 The procedures in this test method describe the measurement of breaking strength, elongation
at break, and energy to break, of pressure sensitive tapes.
1002
[Page extract]
ASTM D5766 / D5766-M
ASTM D5766 is a test method to determine the open-hole tensile strength of multidirectional polymer matrix composite laminates reinforced by high-modulus fibres.
1003
Event
Compressive Crush Force Testing
This webinar will focus on identifying and troubleshooting variables that impact compressive force testing, setting up repeatable compression force tests and establishing consistent testing standards for your products.
1004
[Page extract]
ASTM D3470
This test method covers the determination of the force required to cause a downward-force-while-turning lug-finish closure to be rotated across the container finish lugs (strippage) without downward force being applied to the closure (Type IIA closures)
1005
Event
Introduction to Consumer Packaging Testing
Damaged packaging can not only cost money but also impact brand perception. Consumers are less likely to purchase a product with damaged packaging, or if their product arrives damaged from poor packaging during the shipping and transport process.
1006
[Page extract]
Differences and similarities to other corrugated tests
While TAPPI T 824 focuses on the intrinsic crush strength of pre-fluted medium, other common corrugated tests measure different performance factors:
1007
Event
Fundamentals of Torque Testing
If you have ever struggled to open your favorite bottle of water or jam or required help loosening the lug nuts on your car’s wheels, it is likely due to a case of over-torque.
1008
[Page extract]
What is the 90-degree peel test?
The 90-degree peel test is a mechanical method used to measure the adhesive strength between two bonded materials.
1009
[Page extract]
TAPPI T 825
The flat crush test (1) is a measure of the resistance of the flutes in corrugated board to a crushing force applied perpendicular to the surface of the board under prescribed conditions.
1010
Event
Fundamentals of Torque Testing
If you have ever struggled to open your favorite bottle of water or jam or required help loosening the lug nuts on your car’s wheels, it is likely due to a case of over-torque.
1011
Event
Wire Crimp & Weld Testing Webinar
The only way of really knowing the strength of a crimped terminal is to pull it.
1012
[Page extract]
*corp 01M-01-218
To determine the resistance of seams to slip or break down when placed under a continuous load.
1013
[Page extract]
ASTM D2659
ASTM D2659 determines the mechanical properties of blown thermoplastic containers under columnar crush conditions at a steady rate of compression. Any container, whether blown commercially or in the laboratory, may be used as the test specimen.
1014
Product
Thiết bị đo kiểm tra lực momen xoắn tự động chính xác
Helixa-i
876-501
Helixa-i là thiết bị kiểm tra mô-men xoắn chính xác được điều khiển bằng phần mềm chạy trên PC. Được thiết kế cho các ứng dụng mô-men xoắn chính xác trong đó lực mô-men xoắn có thể rất nhỏ và độ chính xác là ưu tiên.
Với nhiều loại phụ tùng chính xác,…
1015
[Page extract]
Bulk analysis
In industries where powders, granules or pelletised materials are formulated, processed or packaged, maintaining consistency in texture and perf
1016
[Page extract]
Compression
Compression testing is a way of determining how something will react when a compressive force is applied to it. It typically involves measuring the relationship between the applied force and how much the object deforms.
It is performed to:
1017
Sensor
Sensors - Universal Testers (ELS)
Sensors
The OmniTest universal testers use Mecmesin's range of high-resolution precision Enhanced Load Sensors (ELS) to record tensile and compressive loads.
ELSA precision loadcell connects directly to an OmniTest or MultiTest-dV stand and communicates…
1018
Case study
Kiểm tra chứng nhận lưới an toàn xây dựng
Yêu cầu IPS Safety Netting cung cấp và lắp đặt hàng ngàn lưới an toàn cho ngành xây dựng. Lưới được sử dụng để ngăn các ngã và để bảo vệ khỏi các mảnh vỡ rơi xuống.
1019
Case study
Kiểm tra độ bền của bao bì các tông sóng
Yêu cầu Trong nhiều tuần kể từ khi COVID-19 bị giam giữ, đã có một lượng lớn giao hàng tận nhà, thậm chí các gã khổng lồ thương mại điện tử phải vật lộn để đáp ứng nhu cầu và thuê đội ngũ công nhân mới.
1020
[Page extract]
Jewellery & Watch
In jewellery and watch production, alloys, components and other materials must meet the needs of the manufacturing process and the end-product should give good service performance when worn by the customer.
1021
Accessory
Custom-made Safety Guards and Enclosures
PDVguard
Where the standard safety guard does not fulfil your application requirements, Mecmesin can work with you to design and produce a custom-made safety guard to meet your exact requirements. Suitable for any Mecmesin test stand. Previously-designed guards…
1022
Accessory
Charger for touchscreen digital gauges, UK, USB-C, 3-pin square
304-059
For use with Mecmesin touchscreen digital force and torque gauges. With 3 square pins. Commonly used in the UK.
The mains adaptor/charger is a USB-C type:
Input:100-240Vac 50/60Hz 0.6A Max
Output: 5V/3A, 9V/3A,12V/2.25A, 3V-9V/3A 9V-11V/2.45A.
1023
Accessory
Rubber coated jaws for Mec154 Heavy-duty Vice Grip, 20kN, 40 x 60 mm
Mec154-BG
Rubber-faced Jaws (40mm high x 60mm wide) - nickel-plated having 1mm thick layer of nitrile rubber coating.
Opening span = 0 - 32 mm.
For specimens which may get weakened by pinching at the contact-edge of the grip. (e.g. films, filaments, fibres and…
1024
Accessory
Compression Plate Square, Hardened Steel, 196 x 196 mm, QC-20 or QC-32 fitting
Mec36-196-St
MEC36-196-St :-
Square compression plate in hardened steel featuring concentric circles for helping operators to place samples centrally. Also supplied with 4 fixing legs to support the weight of the steel plate. Suitable for hard specimens such as…
1025
Accessory
Blank (smooth) jaws for Mec83 U-Form Pneumatic Vice Grip, 5 kN, 40 x 60 mm
Mec83-B
Blank Jaws (40mm x 60mm) - smooth steel jaw. Allows the user to machine or affix own surface (eg. abrasive 'emery' paper).
Opening span = 0-10mm, 10-20mm or 20-30mm depending on which rod and piston are fitted to the Mec83 body.
Supplied as 0.5 set = 2…