Search results
2076
[Page extract]
Interpreting compressive strength test results
Interpreting results involves more than noting the peak load. Stress–strain curves reveal additional information such as modulus, yield point, and failure mode.
2077
[Page extract]
BS EN 1895
Adhesives, Adhesion tests, Peeling tests, Paper, Paper products, Board (paper), Disposable, Packaging materials, Flexible materials
2078
[Page extract]
ASTM D4533-11
This test method is an index test used to measure the force required to continue or propagate a tear in woven or non-woven geotextiles by the trapezoid method.
2079
[Page extract]
Interpreting test results
Peel strength is typically reported in newtons per metre (N/m) or per 25 mm of bond width (N/25mm), depending on the industry standard. From the force-displacement graph, the following characteristics are analysed:
2080
Event
Brütsch-Rüegger Tools at INNOTEQ 2025
Our trusted distributor, Brütsch-Rüegger Tools, will be exhibiting at INNOTEQ 2025 - the key event for Switzerland’s manufacturing industry.
2081
[Page extract]
ASTM D926-17
ASTM D926 is a test method that covers the determination of plasticity and recovery of unvulcanized rubber by means of the parallel plate plastometer. Uncompounded, compounded, and reclaim rubber may be tested.
2082
[Page extract]
ISO 13935-1
ISO 13935-1:2014 specifies a procedure to determine the seam maximum force of sewn seams when the force is applied perpendicularly to the seam. ISO 13935-1:2014 specifies the method known as the strip test.
2083
[Page extract]
Why torque testing is essential in packaging
Prevents leakage in liquid containers
Ensures seal integrity and prevents contamination
Confirms child-resistant closures are effective and compliant
Improves user experience by avoiding over-tightening
<
2084
[Page extract]
BS EN 2597
BS EN 2597 is test method covering tensile testing on carbon fibre reinforced plastics.
Before conducting BS EN 2597, it is important to read the entire specification. Standards can be obtained from appropriate standard authorities.
2085
[Page extract]
Consumer Products
Mecmesin test solutions for products typically found in the home ...
2086
[Page extract]
ASTM C297
This test method determines the flatwise tensile strength of the core, the core-to-facing bond, or the facing of an assembled sandwich panel.
2087
[Page extract]
FINAT FTM1
This test method is designed to quantify the permanence of adhesion or peelability of self-adhesive pressure sensitive) materials.
2088
[Page extract]
ASTM D6195-03
These test methods cover the determination of properties of a pressure-sensitive adhesive. These test methods are applicable to those adhesives that form a bond of measurable strength rapidly upon contact with another surface.
2089
[Page extract]
ASTM C961
This test method covers a laboratory procedure for determining the lap shear strength of sealants. It also provides information on the adhesive bond of the sealants to the tested substrates.
2090
[Page extract]
BS EN 1492-1
Specifies the requirements related to safety, including methods of rating and testing single-, two-, three-, four-leg and endless sewn flat woven webbing slings, with or without fittings, made of polyamide, polyester and polypropylene man-made fibre web
2091
[Page extract]
Step-by-step guide to conducting a CMT test
Prepare the specimen - Cut to size with clean edges, ensuring flutes remain undamaged, and condition as per the standard.
Calibrate the equipment - Check the load cell and platen alignment.
2093
[Page extract]
ASTM D5656-10
This test method covers the preparation and testing of thick-adherend lap-shear samples for the determination of the stress-strain behavior of adhesives.
2094
[Page extract]
ASTM C674
These test methods cover determination of the modulus of rupture and the modulus of elasticity of fired ceramic whitewares bodies, formed by any fabrication method, and are applicable to both glazed and unglazed test specimens.
2095
[Page extract]
ASTM F607-03
The ASTM F607 test method provides a means of determining the degree to which gasket materials under compressive load adhere to metal surfaces. The test conditions described are indicative of those frequently encountered in gasket applications.
2096
[Page extract]
ASTM F2132-01
This specification provides the performance requirements and associated test procedures for the puncture resistance of materials used in the construction of containers for discarded medical needles and other sharps.
2097
Event
Advanced Engineering 2021 - We would love to see you there!
Who should attend?
Engineering professionals and managers from advanced manufacturing sectors interested in quality assurance testing solutions.
What is the exhibition about?
2098
[Page extract]
ISO 1926
ISO 1926 specifies a method of determining the behaviour of rigid cellular plastics materials when they are subjected to a tensile stress.
2099
[Page extract]
BS EN 2591-418
Describes a method of determining the insertion/extraction forces of female contacts used in elements of electrical and optical connection by means of gauges.
2100
[Page extract]
ASTM D3658
This test method covers the simplistic comparison of strengths of glass/metal joints when the adhesive is cured by ultraviolet (UV) radiation and standard specimens are used and tested under specified conditions of preparation, radiation, and load.