Search results
1226
Page
Giới thiệu về Mecmesin
Mecmesin - Giải pháp cho kết quả bạn có thể tin cậy Từ năm 1977, Mecmesin đã thiết kế các giải pháp kiểm tra lực, vật liệu và mô-men xoắn đáng tin cậy
1227
Case study
Hệ thống lực trượt và ngắt ống tiêm tự động
Yêu cầu Đại dịch COVID-19 đã đặt ra nhu cầu chưa từng có đối với các nhà sản xuất ống tiêm và lọ thuốc.
1228
Case study
Kiểm tra độ nghiền cạnh (ECT) của các tông sóng
Trong những tuần bị giam giữ COVID-19, đã có một lượng lớn giao hàng tận nhà, thậm chí các gã khổng lồ bán lẻ trực tuyến đang phải vật lộn để đáp ứng nhu cầu và thuê đội ngũ công nhân mới. Nghe thấy tiếng gõ cửa để nhận một gói hàng mang lại ch
1229
Sensor
Sensors - Vortex-dV
Torque sensors
A range of 'Smart' interchangeable torque sensors are specially adapted for the Vortex-dV test system. Plug and play for automatic calibration and a range of capacities for all requirements, from 1.5 N.m (13 lbf.in) to 10 N.m (90 lbf.in).…
1230
[Page extract]
Burst testing techniques and equipment
Compressive burst testing
In compressive burst testing, force is applied through a hemispherical probe until the material ruptures.
1231
[Page extract]
ISO 505
ISO 505 specifies a method of test for the measurement of the propagation resistance of an initial tear in textile conveyor belts, either in full thickness or of the carcass only.
1232
[Page extract]
ISO 7886-4
This document specifies requirements for sterile single-use hypodermic syringes made of plastic and rubber materials with or without needle, and intended for the aspiration of fluids or for the injection of fluids immediately after filling and of design
1233
[Page extract]
Interpreting test results
Peel strength is typically reported in newtons per metre (N/m) or per 25 mm of bond width (N/25mm), depending on the industry standard. From the force-displacement graph, the following characteristics are analysed:
1234
[Page extract]
ECT vs BCT
While ECT measures the compressive strength of the board material, the box compression test (BCT) measures the strength
1235
[Page extract]
ASTM D3410 / D3410M
ASTM D3410 determines the compressive properties of polymer matrix composite materials reinforced by high-modulus fibers.
1237
Case study
Kiểm tra độ bền kéo của lưới đánh cá theo ISO1806
Yêu cầu Lưới đánh cá là một trong những công cụ quan trọng trong đánh bắt thương mại và có nhiều loại ngư cụ chủ động và bị động. Việc đứt lưới trong quá trình đánh bắt là rất phổ biến, gây ra nhiều vấn đề cho nghề cá và môi trường.
1238
[Page extract]
ISO 11608-5
This part of ISO 11608 specifies requirements and test methods for the automated functions of needle-based injection systems with automated functions (NIS-AUTO), for the administration of medicinal products in humans.
1239
Event
Brütsch-Rüegger Tools at INNOTEQ 2025
Our trusted distributor, Brütsch-Rüegger Tools, will be exhibiting at INNOTEQ 2025 - the key event for Switzerland’s manufacturing industry.
1240
[Page extract]
How is compression texture testing performed?
Test methods and parameters
A typical test places the sample on a stable platform beneath a compression plate or probe.
1241
[Page extract]
ISO 36
ISO 36 determines the strength required to separate two plies of fabric bonded together with rubber, or a rubber and a fabric ply bonded together. This test is referred to as a “T-peel” test, because as the two adherends are pulled apart, they form the
1242
[Page extract]
ISO 7623
ISO 7623 specifies a method for determining the bond strength of metal cords to their surrounding coating, either in the initial state or after thermal treatment.
1243
[Page extract]
Key test standards for cone penetration
BS EN 14372 overview
BS EN 14372 is a key European standard for cutlery and feeding utensils intended for children up to three years of age.
1244
[Page extract]
Application in food texture analysis
Tension methods replicate real-world conditions experienced by food products during production, handling, and consumption.
1245
[Page extract]
FAQs
Find answers to common questions about syringe testing and ISO 11040-4:
1246
[Page extract]
ASTM D6641 / D6641M - 16e1
The ASTM D6641 test method determines compressive properties of polymer composite materials by applying combined end-loading and shear-loading using a combined loading compression (CLC) fixture.
1247
[Page extract]
Why is double lap shear testing important?
The double lap shear test is widely used to determine the performance of adhesives in structural and semi-structural applications. It allows engineers to:
1248
[Page extract]
When High Ultimate Tensile Strength is a Disadvantage
While high UTS materials are strong, they can also be brittle and less ductile.
1249
[Page extract]
Why Mecmesin for puncture resistance testing
Mecmesin designs and manufactures precision puncture resistance testing systems to meet the requirements of ASTM and ISO standards.
1250
[Page extract]
ASTM D4501-01
This test method describes a procedure and fixture used to determine shear strengths of adhesives used to bond materials with moduli higher than the modulus of the adhesive.