Search results
101
Accessory
3/8" Upper Chuck Assembly for use on Helixa sensors
432-615
A standard self-centering 3-jaw chuck with key.
It has a maximum ⅜" (9.5 mm) opening and is connected to the Helixa torque sensor via an adaptor with female ⅜" square hole.
Used to secure a variety of test specimens for torque applications of 1.5 - 10…
102
Case study
Syringe tube pull-off testing
Customised engineering example
Pull-off tensile tests require careful gripping of the separating parts in order to avoid distorting them and therefore artificially weakening the joint.
103
Case study
End float test of inhaler cap
Requirement
'End float is the displacement in mm of a product', in this case the dispensing cap closure of the inhaler measured at a specific load.
104
Case study
Child safety - force to extract lighter
Requirement
The customer manufactures lighters and is currently developing a case/guard designed to increase the safety for children.
105
Case study
Testing fluid control valves and seals
Requirement
A typical gas lift system for oil and gas production requires a set of valves to operate along the production tubing down the drilling well.
106
Case study
Aircraft brake unit spring testing
Requirement
The Aircraft Wheels and Brakes department at British Airways plc are responsible for the repair and overhaul of the aircraft brake units on the Boeing 737, 747, 757, 777 and Airbus A319, A320 and A321 aircraft.
107
Case study
Plastic film tension test
Requirement
The customer uses a double layer plastic film for packaging film for packaging of pet food and confectionary.
108
[Page extract]
ISO 13939
Describes a method of comparing the performance test results of foil journal bearings, which are lubricated by air (gas) and supported by hydrodynamic force generated by the rotation of the rotating shaft.
109
Case study
PCB Solder Joint Shear
Requirement
Millennnium Microtech Thailand, part of Microchip Technology Inc Thailand operates a manufacturing, packaging and testing plant for Printed Circuit Board (PCB) Integrated Circuit (IC) components.
110
Case study
Box crush test (BCT) and transit packaging compression testing
Customised engineering example
Boxes for the consumer and transit packaging industries must be as light as possible whilst still retaining a robustness to contain and protect their contents and also have the strength to stand up to shipping, ha
111
Case study
Peel strength and elongation testing of water-blocking tape
Requirement
Ekstel d.o.o. manufactures a range of water-blocking tapes under the branding X-tra tapes®, which have specific applications in the cable industry.
112
Case study
Detonator shock tubing
Requirement
A manufacturer of non-electric shock detonator tubing for industrial applications had a specialist tensile testing requirement.
113
Case study
Page pull strength test
Requirement
Mecmesin collaborated with a customer to design and develop a force measurement system to determine book binding adhesive strength in retaining individual pages.
114
Case study
Medical sharps bin puncture resistance
Customised engineering example
International standards (ASTM F2132, BS 7320, BS 23907) specify the puncture resistance of medical sharps containers.
115
Case study
Crimp testing cables
Requirement
A leading British cable assembly manufacturer, Telecom Connections Limited, who provide customers in the telecoms and electronics industries with quality cable assemblies and harnesses, wanted to test their wire crimp terminals to m
116
[Page extract]
ASTM F2592
1.1 This test method covers the measurement of force displacement characteristics of a membrane switch.
117
Event
Medical Device Testing: Needle sharpness and syringe actuation testing (with 21 CFR Part 11 compliance)
Hypodermic needles are tested to determine their efficacy in piercing elastomer closures on vials and how their design influences the ease of insertion into the patient's skin, influencing pain and skin trauma.
The smooth and consistent operat
118
Event
Critical strength: Perfecting catalyst and pellet crush testing
Catalysts are widely used in industrial processes where yield and time issues are critical to forming a product as soon as possible.
119
Case study
Laminated auto windshield perimeter seal peel testing
Requirement
The windshield (or windscreen) in your car is made of laminated glass, which is designed to offer the highest levels of safety in the event of a crash.
120
Case study
Hot air balloon cloth tensile strength and tear-resistance testing
Requirement
Ultramagic is the second largest hot air balloon manufacturer in the world.
For obvious safety reasons, the material used must conform to strict standards applicable to the aeronautical industry.
121
Accessory
MultiTest 0.5 bellows assembly (1200 mm)
432-473
Optional bellows for the MultiTest 0.5 range of single-column test stands. Used to protect against dust and particle ingress and splash into the column.
Note that fitting of bellows reduces throat depth on test stand by 18mm.
Order with a MultiTest 0.5…
122
Accessory
Smooth jaws for Mec11-20 Scissor Grip, 20 kN, 25 x 50 mm
Mec11-20-B
Blank Jaws (25mm x 50mm) - smooth steel jaw. Allows user to machine or affix own surface.
Supplied as 0.5 set = 2 jaws (left & right). Order any combination of 2 half sets of jaws to fit into a pair of MEC11-20 Scissor Grips (upper & lower)
123
Accessory
180 degree Peel Jig for FPT-H1
432-636
This raised peel table fits the Mecmesin FPT-H1 for 180 degree peel testing to standard methods, for pressure sensitive tapes and labels. It accepts interchangeable float glass and stainless steel sample plates (available separately). Includes peel hook…
124
Accessory
Smooth jaws for Mec11-5 Scissor Grip, 5 kN, 20 x 50 mm
Mec11-5-B
Blank Jaws (20mm x 50mm) - smooth steel jaw. Allows user to machine or affix own surface.
Supplied as 0.5 set = 2 jaws (left & right). Order any combination of 2 half sets of jaws to fit into a pair of MEC11-5 Scissor Grips (upper & lower)
125
Accessory
Rubber coated jaws for Mec154 Heavy-duty Vice Grip, 20kN, 40 x 60 mm
Mec154-BG
Rubber-faced Jaws (40mm high x 60mm wide) - nickel-plated having 1mm thick layer of nitrile rubber coating.
Opening span = 0 - 32 mm.
For specimens which may get weakened by pinching at the contact-edge of the grip. (e.g. films, filaments, fibres and…