Search results
952
[Page extract]
The role of ECT in quality assurance
The Edge Crush Test is a widely used measure for predicting box stacking performance.
953
[Page extract]
Torque testing methods and equipment
Equipment used
Strip torque testing can be carried out using:
954
[Page extract]
Applications across industries
T-peel testing is widely used in industries where adhesive bonds are critical:
955
[Page extract]
Bakery
Consumers have very particular expectations of how bakery products should feel and behave during consumption. Deviations from this ideal are often perceived as a loss in quality.
956
[Page extract]
Case studies and real-world examples
Food sachet packaging
In a recent study, our equipment was used to test the burst strength of multilayer foil sachets used for single-serve food products.
957
[Page extract]
Grab method vs strip method
Compared with the strip method (as defined by ISO 13934-1), which grips the full width of the fabric, the grab method
958
[Page extract]
Introduction to tension and compression testing
Tension and compression testing are among the most widely used mechanical testing methods for evaluating how a material or component performs under applied loads.
959
[Page extract]
Applications of compressive shear testing
Compressive shear testing is applied across multiple industries where materials must withstand shear stresses while compressed.
960
[Page extract]
Testing solutions and equipment
Essential equipment
Cone point probe - typically 8 mm in diameter with capacity for up to 500 N.
961
[Page extract]
Applications of floating roller peel testing
Floating roller peel testing is employed to verify both material selection and process stability in various high-performance sectors:
962
[Page extract]
Key standards for double rip tongue tear testing
ASTM D751-06 for coated fabrics
ASTM D751-06 defines test methods for coated fabrics, including the d
963
[Page extract]
Why is double lap shear testing important?
The double lap shear test is widely used to determine the performance of adhesives in structural and semi-structural applications. It allows engineers to:
964
[Page extract]
Significance of connector extraction resistance
Extraction resistance is the connector’s ability to maintain a secure fit during use while still allowing disconnection when necessary. This is especially important where connectors are repeatedly mated and unmated, such as:
965
[Page extract]
How is torque testing in packaging performed?
Torque testing can be carried out using manual or automated methods, depending on production volume, precision requirements
966
[Page extract]
Speak to an Expert
The Concora Crush Test, as defined in TAPPI T 824, is a critical step in corrugated medium evaluation.
967
[Page extract]
Secant modulus compared to other moduli
Different moduli are used to describe the stiffness of materials, each calculated at different points on the stress-strain curve:
968
[Page extract]
What is the grab method?
The grab method is a tensile testing technique where only the centre of a fabric specimen is gripped during testing — typically using 100 mm × 150 mm test specimens with a 50 mm wide clamp
969
[Page extract]
Case studies and applications
Real-world applications of compressive strength testing are prevalent in various industries:
970
[Page extract]
Introduction to tear resistance testing
Tear resistance testing is a critical mechanical property assessment for flexible materials such as plastics, elastomers, coated fabrics and textiles.
971
[Page extract]
FAQs about Ultimate Tensile Strength
What is ultimate tensile strength?
Ultimate tensile strength (UTS) is the highest amount of tensile stress a material can resist before it breaks.
972
[Page extract]
Key methods in shear stress measurement
There are several approaches to measuring shear stress, with rotational shear testing and torsion-based techniques among the most widely used.
973
[Page extract]
Electronic components and assemblies
Electrical assemblies rely on a collection of electrical components that have been connected together on a PCB or other surface to perform a specific function.
974
[Page extract]
Burst testing techniques and equipment
Compressive burst testing
In compressive burst testing, force is applied through a hemispherical probe until the material ruptures.
975
[Page extract]
Key test standards for ball burst testing
ASTM D3787 – Constant-rate-of-traverse (CRT) method
This standard outlines a method for determining the bursting strength of