Search results
1326
[Page extract]
BS EN 12430
A compressive point load (of a certain cross-sectional area) is applied to a specimen of thermal insulating product, such as a mineral wool sandwich panel.
1328
[Page extract]
ASTM D575-91
These test methods cover two test procedures for determining the compression-deflection characteristics of rubber compounds other than those usually classified as hard rubber and sponge rubber.
1329
[Page extract]
ASTM D229
ASTM D229 is a test method, which provides useful engineering information for evaluating the mechanical behaviour of rigid electrical insulation at elevated temperature.
1330
[Page extract]
BS ISO 7322
This International Standard specifies test methods for the determination of the following characteristics of composition cork (= product obtained from the agglutination of cork granules with the addition of a binder generally not derived from cork cells
1331
[Page extract]
MIL AS23190A
AS23190 is a procurement specification that covers a series of plastic and metal components and devices used for the tying, positioning, and supporting cable, cable assemblies, wire, and wire bundles in electrical, electronic and communication equipment
1332
[Page extract]
ASTM D3916
ASTM D3916 is a test method for determining the tensile properties of pultruded, glass-fiber-reinforced thermosetting plastic rod of diameters ranging from 3.2 mm to 25.4 mm.
1333
[Page extract]
ISO 6789
Wrenches, Torque, Hand tools, Screwdrivers, Marking, Approval testing, Quality control, Calibration
1334
Event
T-Peel (Adhesion Strength) Testing
This webinar will focus on the most common approach to measuring the adhesion strength of two materials bonded together with an adherent.
1335
[Page extract]
DIN EN 61238-1
Electric connectors, Crimped connectors, Electric cables, Power cables, Electric conductors, Electric wires, Copper, Aluminium, Temperature, Classification systems, Type testing, Short-circuit current tests, Resistance measurement, Mechanical testing, T
1336
[Page extract]
ISO 10354
Simulates in a qualitative manner the forces and effects on an adhesive-bonded joint at a metal-adhesive/primer interface. It can also be used as a method of checking the surface preparation of substrates.
1337
Event
Materials Testing: Theory and Practice Pt. 2
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
1338
[Page extract]
ASTM D1004
ASTM D1004-13 covers the determination of tear strength or tear resistance of flexible plastic film and sheeting. The site of tear is initiated by a high stress concentration caused by the 90° angle in the specimen.
1339
Event
Child Resistant Closure Torque Testing
Medical, Pharmaceutical and Chemical Packaging takes product safety seriously.
1340
[Page extract]
BS EN ISO 527-1
BS EN ISO 527-1 specifies the general principles for determining the tensile properties of plastics and plastic composites under defined conditions.
1341
[Page extract]
ISO 29862
This test standard specifies a series of methods for the determination of peel adhesion properties of self adhesives tapes.
1342
Event
Materials Testing: Theory and Practice Pt. 1
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
1343
[Page extract]
ASTM D6068-10
This test method covers the determination of the J-integral versus crack growth resistance (J-R) curves for polymeric materials.
1344
[Page extract]
ASTM F806-99a
ASTM F806 is a test method that covers determination of the short-time compressibility and recovery at room temperature of laminated composite gasket materials.
1345
Event
Makers Hackathon, June 16-18th 2022, Malmö, Sweden
Who should attend?
Quality Managers, design/product engineers and materials specialist.
What is the exhibition about?
1346
[Page extract]
ISO 1827
ISO 1827 specifies methods for the determination of the modulus in shear and the strength of bonds of rubber to metal or other rigid plates, using rubber bonded between four parallel plates.
1347
[Page extract]
BS EN 671-2
Fire hydrants, Fire hoses, Firefighting equipment, Flexible pipes, Fire safety in buildings, Design, Performance, Performance testing, Conformity, Approval testing, Corrosion tests, Ageing tests, Flow measurement, Impact testing, Pressure testing, Hydra
1348
[Page extract]
ASTM D1414
ASTM D1414 is used to measure the mechanical properties of vulcanized rubber o-rings. Mecmesin test equipment is relevant to the tensile testing part of this standard, which covers a variety of different tests.
1349
Event
Wire Terminal Strength & Crimp Testing Webinar
The only way of really knowing the strength of a crimped terminal is to pull it.
1350
[Page extract]
ISO 9073-7
Specifies a method for the determination of the bending length of nonwovens. Gives an equation for calculating the flexural rigity of the fabric from the bending length. Does not apply to composites and laminates.