Search results
726
[Page extract]
TAPPI T 284
This test evaluates the ability of corrugating medium to contribute to the compression strenght of a corrugated box.
727
[Page extract]
ISO 8094
ISO 8094 specifies a test method for determining the adhesion strength of the cover to the core layer. It applies exclusively to steel cord conveyor belts.
728
[Page extract]
Applications across sectors
Texture testing in food manufacturing
Bread softness for freshness control, snack crispness for quality assurance, firmness in
729
Case study
Cable duct strength testing
Customised engineering example
Our customer manufactures tubes and ducts for routing of cables and optical fibres. Installation of these uses blowing, pushing and pulling techniques.
730
Case study
Electrical connector insertion and withdrawal forces
Customised engineering example
Push-fit electrical connectors with hole or dimple detents (also known as 'spade terminals') must offer a firm but practical fit.
731
[Page extract]
ASTM D5748-95
This test method determines the resistance of a stretch wrap film to the penetration of a probe at a standard low rate, a single test velocity.
732
[Page extract]
ISO 6425
This document specifies requirements and test methods for divers' watches and for saturation divers' watches for use in deep diving (see Annex A which deals with watches for saturation diving).
733
Event
Wine & Spirits: Pull Tab & Twist Cap Testing
Canned wine and seltzer drinks have a clear upside that makes their popularity soar: Convenience. As well as being lighter to carry, less potentially fragile, eliminating the corkscrew, and even a glass makes it ideal for social gatherings.
734
Page
You have been subscribed to the Mecmesin newsletter
Thank you
We hope you enjoy the regular updates on our developments in force, materials and torque testing.
735
[Page extract]
TAPPI T 400
This method describes procedures for obtaining a representative sample for testing.
736
[Page extract]
ASTM C273/C273M
This test method is used to determine core shear properties of a sandwich construction material using loading plates bonded to the outer surfaces or skins (facesheets).
737
[Page extract]
BS EN ISO 9626
This International Standard specifies the dimensions, surface and mechanical properties of normal- and thin-walled tubing of designated metric sizes 3,4 mm to 0,3 mm, and of extra-thin-walled tubing of designated metric sizes 2,1 mm to 0,6 mm.
738
[Page extract]
TAPPI T 576
This test method decribes the procedure, using constant-rate-of-elongation, for determining three tensile breaking properties of towel and tissue: tensile strength, stretch, and tensi;e energy absorption.
739
[Page extract]
BS EN ISO 8295
ISO 8295 specifies a method for determining the coefficients of starting and sliding friction of plastics film and sheeting when sliding over the same or other substances. It is intended to be used for non-sticky plastic film and sheeting of up to appr
740
[Page extract]
TAPPI T 839
This method describes procedures for determining the edgewise compressive strenght, with flutes vertical, loading perpendicular to the axis of the flutes, of a short column of single, double, or triple-wall corrugated fiberboard.
741
Case study
Seed bottle closure torque testing
Requirement
The Royal Botanic Gardens, Kew, have undertaken an international conservation initiative to preserve seed specimens of over 24,000 plant species, protecting them from extinction at the Millennium Seed Bank at Wakehurst Place, West
743
[Page extract]
ASTM D1321
This test method covers the empirical estimation of the consistency of waxes derived from petroleum by measurement of the extent of penetration of a standard needle.
744
[Page extract]
TAPPI T 809
This method describes a procedure for measuring the crushing resistance of a laboratory fluted strip of corrugating medium and provides a means of estimating, in the laboratory, the potential flat crush resistance of a corrugated board.
745
Page
Contact us about automation
Thank you for contacting our sales team about automating your testing
One of our Senior Technical Sales Engineers will reach out to you within 2 working days to discuss your requirements.
746
[Page extract]
Applications across industries
Mecmesin torque to turn systems are used in sectors including:
747
Case study
Plastic film tension test
Requirement
The customer uses a double layer plastic film for packaging film for packaging of pet food and confectionary.
748
Case study
Top-load testing PET bottles
Requirement
Esterform Packaging manufacture more than a million PET bottles and preforms per day for major processors of bottled water, juices, soft drinks, dairy and household products.
749
[Page extract]
ASTM D6109-19
ASTM D 6109 determines the flexural properties for any solid or hollow manufactured plastic lumber product of square, rectangular, round, or other geometric cross section that shows viscoelastic behavior.
750
[Page extract]
Case studies and real-world applications
In beef grading, Warner-Bratzler shear testing confirms tenderness classification, ensuring export standards are met.