Search results
2626
[Page extract]
BS EN ISO 8670-2
Two part test on filled bags:
1) 20 N tensile flange seal test, pulled in two directions in turn, at 180 degrees, in shear plane across flange, bag held by transparent custom plate
2627
[Page extract]
DIN EN 61238-1
Electric connectors, Crimped connectors, Electric cables, Power cables, Electric conductors, Electric wires, Copper, Aluminium, Temperature, Classification systems, Type testing, Short-circuit current tests, Resistance measurement, Mechanical testing, T
2628
[Page extract]
Bollard/roller grips
Bollard grips - provide a rounded surface around which a specimen is curved or wound several times before its end is clamped between jaws.
2629
[Page extract]
ASTM D6396-99
This test method covers procedures used to assemble, evaluate and test pipe thread sealants.
2630
[Page extract]
ISO 188
ISO 188:2011 specifies accelerated ageing or heat resistance tests on vulcanized or thermoplastic rubbers. Two methods are given:
2631
[Page extract]
ASTM D1709-03
These test methods cover the determination of the energy that causes plastic film to fail under specified conditions of impact of a free-falling dart.
2632
[Page extract]
BS EN ISO 6789
Wrenches, Torque, Hand tools, Screwdrivers, Marking, Approval testing, Quality control, Calibration
2633
[Page extract]
BS EN 1799
Applicable to both vertical and horizontal surfaces. To be read in conjunction with BS EN 1504-1:2005
Concretes, Structures, Adhesives, Surfaces, Repair, Performance testing, Physical testing, Flow, Specimen preparation, Test equipment
2634
[Page extract]
BS EN ISO 314-1
This test standard specifies methods for determining the bonding quality of veneer plywood, blockboard and laminboard by shear testing.
2635
[Page extract]
BS EN 1707
Syringes, Conical fittings (syringes), Injection instruments, Locking and locating devices, Fitting, Pipe fittings, Medical equipment, Medical instruments, Blood transfusion equipment, Dimensions, Dimensional tolerances, Performance testing, Leak tests,
2636
[Page extract]
BS EN ISO 9004
BS EN ISO 9004 provides guidance on achieving sustainable success through quality management. The European standard can be applied to all organisations across all sectors.
2637
[Page extract]
BS 6965-1
Cartons, Board (paper), Paper products, Crease-recovery tests, Creasing tests, Folding, Test equipment, Specimen preparation, Testing conditions, Reproducibility, Containers, Blanks, Stiffness, Boxboard
2638
[Page extract]
BS EN 843-1
EN843-1 describes methods for determining the nominal flexural strength of advanced monolithic technical ceramic materials at ambient temperature.
2639
[Page extract]
ASTM D5-06e1
This test method covers determination of the penetration of semi-solid and solid bituminous materials. The needles, containers and other conditions described in this test method provide for the determinations of penetrations up to 500.
2640
[Page extract]
ASTM D3931
This test method covers the determination of comparative shear properties of gap-filling adhesives in wood-to-wood joints at specified thicknesses of bondline in the dry condition, when tested on standard specimens under specified conditions of preparat
2641
[Page extract]
BS ISO 6939
Applicable to spun single and folded yarns of any fibre or mixture of fibres manufactured by any spinning systems. Not recommended for testing filament yarns, glass yarns, more complex structures such as cabled yarns or cords.
2642
[Page extract]
29 073-3
Textiles: test method for nonwovens; Part 3: Determination of tensile strength and elongation.
2643
[Page extract]
BS EN 50289-3-16
Communication cables, Electric cables, Communication transmission lines, Mechanical testing, Tensile testing, Tensile strength, Performance testing
2644
[Page extract]
ASTM C480
This test method covers the determination of the creep characteristics and creep rate of flat sandwich constructions loaded in flexure, at any desired temperature.
2645
[Page extract]
ISO 13445
Specifies a method for the determination of the shear strength of adhesives used to bond materials with elastic moduli higher than the elastic modulus of the adhesive.
2646
[Page extract]
ASTM D903-98
ASTM D903 is a test procedure used to determine the strength of adhesive bonds.
2647
[Page extract]
ISO 13955
ISO 13955 is used to assess the cohesion of a PE pipe/electrofusion socket or saddle assembly. Applicable to pipes with a nominal outside diameter between 16 mm and 225 mm
2648
[Page extract]
Probes
Probes are designed primarily for penetration and puncture resistance testing. There are a variety of tip profiles and sizes available (e.g. cone, chisel, radiused) to simulate the real-world conditions under which a specimen may be compressed.
2649
[Page extract]
BS 5081-1
A mechanical testing machine is used to move the syringe plunger and to aspirate and expel water, whilst the force exerted and the plunger travel are recorded.
2650
[Page extract]
TAPPI T 821
Measures the force required to separate corrugated board between the flute tips of corrugated medium and its linerboard facings.