Search results
2551
[Page extract]
ASTM E8/E8M-13a
These test methods cover the tension testing of metallic materials in any form at room temperature, specifically, the methods of determination of yield strength, yield point elongation, tensile strength, elongation, and reduction of area.
2552
Event
Materials Testing: Theory and Practice Pt. 2
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
2553
[Page extract]
BS EN ISO 7389
This International Standard specifies a method for the determination of the elastic recovery of sealants after maintained extension.
2554
[Page extract]
BS EN 319
EN319 specifies a method for determining the resistance to tension perpendicular to the plane of the board (“internal bond”) of particleboards, fibreboards, and cement-bonded particleboards.
2555
[Page extract]
TAPPI T 549
This method describes a horizontal plane procedure for the determination of the coefficient of static and kinetic friction of paper measured when sliding against itself.
2556
[Page extract]
BS EN 16732
Slide fasteners, Fasteners (clothing), Grades (quality), Performance, Colour fastness, Dimensional tolerances, Marking, Mechanical testing, Strength of materials, Locking tests, Shrinkage, Dimensional changes, Testing conditions, Sampling methods
2557
[Page extract]
ASTM D6396-99
This test method covers procedures used to assemble, evaluate and test pipe thread sealants.
2558
Event
Materials Testing: Theory and Practice Pt. 1
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
2559
[Page extract]
BS EN 1799
Applicable to both vertical and horizontal surfaces. To be read in conjunction with BS EN 1504-1:2005
Concretes, Structures, Adhesives, Surfaces, Repair, Performance testing, Physical testing, Flow, Specimen preparation, Test equipment
2560
[Page extract]
ASTM C158
These test methods cover the determination of the modulus of rupture in bending of glass and glass-ceramics. These test methods are applicable to annealed and prestressed glasses and glass-ceramics available in varied forms.
2561
[Page extract]
TAPPI related
TAPPI Standards compared to Related Standards of ISO and ASTM (revised August 2011)
2562
[Page extract]
ASTM D5-06e1
This test method covers determination of the penetration of semi-solid and solid bituminous materials. The needles, containers and other conditions described in this test method provide for the determinations of penetrations up to 500.
2563
[Page extract]
ASTM D3658
This test method covers the simplistic comparison of strengths of glass/metal joints when the adhesive is cured by ultraviolet (UV) radiation and standard specimens are used and tested under specified conditions of preparation, radiation, and load.
2564
[Page extract]
BS 7320
This British Standard specifies requirements for sharps containers intended to hold potentially infectious medical waste comprised largely of devices which can readily cause physical injury e.g. scalpel blades, hypodermic needles and syringes.
2565
[Page extract]
ASTM C1028
This test method covers the measurement of static coefficient of friction of ceramic tile or other surfaces under both wet and dry conditions while utilizing Neolite heel assemblies. This test method can be used in the laboratory or in the field.
2566
[Page extract]
TAPPI T 816
administratively withdrawn 'for lack of timely review'
ASTM D4521 equivalent, withdrawn
2567
[Page extract]
ISO 20344
This Standard specifies methods for testing footwear designed as personal protective equipment.
8 groups of tests from dimensions to mechanical properties and fluid resistance.
Supplemented by ISO 20345
2568
[Page extract]
Probes
Probes are designed primarily for penetration and puncture resistance testing. There are a variety of tip profiles and sizes available (e.g. cone, chisel, radiused) to simulate the real-world conditions under which a specimen may be compressed.
2569
[Page extract]
IEC 62137-1-1
The test method described in IEC 62137-1-1:2007 is applicable to gull-wing lead surface mounting components.
2570
[Page extract]
TAPPI T 284
This test evaluates the ability of corrugating medium to contribute to the compression strenght of a corrugated box.
2571
[Page extract]
BS EN 12430
A compressive point load (of a certain cross-sectional area) is applied to a specimen of thermal insulating product, such as a mineral wool sandwich panel.
2572
Specials
Vector instruments - Intuitive touchscreens
Intuitive touchscreen
The most advanced touchscreen force and torque gauges, powered by Vector OS.
Handheld instruments built for tough environments to deliver accuracy and reliability.
2573
[Page extract]
BS EN 12346
Gymnastics equipment, Wall bars, Ladders, Sports equipment, Indoor sports equipment, Design, Dimensions, Height, Dimensional tolerances, Shape, Strength of materials, Safety measures, Marking, Instructions for use, Equipment safety, Mechanical testing,
2574
[Page extract]
NF B 57 100
Section 8 covers the measurement of the tensileforce to extract a natural or synthetic cork from a still wine bottle or from a standardised glass tube, which simulates the profile of the neck of a wine bottle.
2575
Event
Wine & Spirits Capping: Cork Pull & Twist Caps
Wine packaging has a great influence on the quality of the product delivered to the customer.