Search results
2601
[Page extract]
EN 14509
This draft European Standard is submitted to CEN members for second formal vote. It has been drawn up by the Technical Committee
CEN/TC 128.
This covers a very wide range of tests including coatings, strengths etc.
2602
[Page extract]
BS EN 2591-417
Defines a method of determining the tensile strength of crimped connections used in elements of electrical and optical connection.
2603
[Page extract]
ISO 4674-1
Describes two methods for determining the forces necessary to initiate and propagate tearing of a coated fabric using the constant rate of tear method. The methods described are:
method A: tongue tear
method B: trouser tear
2605
[Page extract]
ISO 2409
Describes a test method for assessing the resistance of paint coatings to separation from substrates when a right-angle lattice pattern is cut into the coating, penetrating through to the substrate.
2606
[Page extract]
*corp QPF-MC-1209 B
*Strictly confidential*
L'Oreal to methods for shear and penetration testing of lipsticks, deodorants etc.
2607
[Page extract]
TAPPI T 400
This method describes procedures for obtaining a representative sample for testing.
2608
[Page extract]
TAPPI T 841
This method describes procedures for determining the edgewise compressive strength, parallel to the flutes, of a short column of single wall and double wall corrugated fiberboard.
2609
[Page extract]
TAPPI T 825
The flat crush test (1) is a measure of the resistance of the flutes in corrugated board to a crushing force applied perpendicular to the surface of the board under prescribed conditions.
2610
[Page extract]
BS EN 1155
Closing and check mechanisms, Door closers, Electrically-operated devices, Ironmongery (buildings), Classification systems, Design, Performance, Durability, Temperature-rise limit, Test equipment, Sampling methods, Performance testing, Temperature, Elec
2612
[Page extract]
BS EN 671-2
Fire hydrants, Fire hoses, Firefighting equipment, Flexible pipes, Fire safety in buildings, Design, Performance, Performance testing, Conformity, Approval testing, Corrosion tests, Ageing tests, Flow measurement, Impact testing, Pressure testing, Hydra
2613
[Page extract]
BS EN ISO 10590
This International Standard specifies a method for the determination of the influence of water immersion on the adhesion/cohesion properties at maintained extension of sealants used in joints in building construction.
2614
[Page extract]
BS EN 12430
A compressive point load (of a certain cross-sectional area) is applied to a specimen of thermal insulating product, such as a mineral wool sandwich panel.
2615
[Page extract]
ASTM D5170-98
This test method covers the measurement of the peel strength of hook and loop touch fasteners using a recording constant-rate-of-extension tensile testing machine (CRE).
2616
[Page extract]
Câu hỏi thường gặp về mô đun cắt
Mô đun cắt được kiểm tra như thế nào? Mô đun cắt được đo bằng thử nghiệm xoắn hoặc dụng cụ thử nghiệm cắt áp dụng cho các mẫu rắn hoặc mẫu liên kết.
2617
Sensor
Cảm biến - Vortex
Cảm biến mô-men xoắn Phạm vi ITC của cảm biến mô-men xoắn có thể hoán đổi cho nhau được điều chỉnh đặc biệt cho hệ thống thử nghiệm Vortex. Plug and play để hiệu chuẩn tự động và có sẵn 5 công suất khác nhau cho mọi yêu cầu, từ 0 - 0,3 Nm (0 - 2,7 lbf.in…
2618
Software
Phần mềm VectorPro MT
Phần mềm VectorPro® MT VectorPro MT là một gói phần mềm thử nghiệm vật liệu tiên tiến được phát triển để thực hiện các thử nghiệm kéo, cắt, uốn và nén trên toàn bộ một loạt các vật liệu. Trình bày dữ liệu đo lường dưới dạng đồ họa và phát hành các báo cáo…
2619
Location
Min Ittapichai, Mecmesin/PPT Group (Asia)
PPT Asia Co. Ltd.
200 Tossapon Building, 3rd Floor, Room 3D,
Ratchadapisek Rd., Huai Khwang,
Bangkok 10310
Thailand
2621
[Page extract]
Bollard/roller grips
Bollard grips - provide a rounded surface around which a specimen is curved or wound several times before its end is clamped between jaws.
2622
Location
Poly-Test Instruments
Machine Park 38 - Unit 16,
Francis Road,
Anderbolt,
Boksburg 1459,
South Africa