Search results
1951
[Page extract]
BS 3531-5.6
For breaking torque and angle rotation at failure for metal bone screws for surgery specified in BS 3531-5.3.
1952
Product
Đồng hồ đo lực và momen xoắn màn hình cảm ứng
VFTI
850-610
Một đơn vị hiển thị màn hình cảm ứng mạnh mẽ và linh hoạt để sử dụng với phạm vi cảm biến lực và mô-men xoắn 'Thông minh' có thể hoán đổi cho nhau của Mecmesin. Lý tưởng cho việc kiểm tra khi yêu cầu chính về độ chính xác và tính linh hoạt cao.
VFTI ,…
1953
[Page extract]
PSTC 131
SCOPE
1.1 The procedures in this test method describe the measurement of breaking strength, elongation
at break, and energy to break, of pressure sensitive tapes.
1954
[Page extract]
BS EN ISO 13934-2
Part 2 of ISO 13934-2 specifies a procedure for the determination of the maximum force of textile fabrics known as the grab test.
1955
[Page extract]
*corp QAC-MC-844
Confidential to l'Oreal
The aim of this test is to check that folding boxes form properly so as to ensure their fluidity of distribution on the filling and packing lines.
1956
[Page extract]
ASTM D5467 / D5467M-97
ASTM D5467 is a test method that determines the in-plane compressive properties of polymer matrix composite materials reinforced by high-modulus fibers in a sandwich beam configuration.
1957
[Page extract]
ASTM D3810
This test method covers the determination of or the recommendation for minimum application torque that results in a fully degraded removal torque that is at a level greater than the maximum expected reverse-ratchet torque for a Type IA child-resistant c
1958
[Page extract]
ISO 6237
Specifies a method for determining the shear strength of wood-to-wood adhesive bonds, with a standard specimen loaded in tension and under specified conditions of preparation, conditioning and testing.
1959
Event
Fundamentals of Food Texture Testing and Analysis
Texture cannot be controlled unless it measured in a consistent and repeatable manner.
1960
[Page extract]
ISO 1798
ISO 1798 specifies a method for determining the strength and deformation properties of flexible cellular materials when a test piece is extended at a constant rate until it breaks.
This test standard is equivalent to BS EN ISO 1798:2008
1961
[Page extract]
ISO 36
ISO 36 determines the strength required to separate two plies of fabric bonded together with rubber, or a rubber and a fabric ply bonded together. This test is referred to as a “T-peel” test, because as the two adherends are pulled apart, they form the
1962
[Page extract]
ASTM D6264 /D6264M-17
In ASTM D6264 a quasi-static indentation (QSI) test method is used to obtain quantitative measurements of the damage resistance of a continuous-fibre-reinforced composite material to a concentrated indentation force
1963
[Page extract]
ASTM D3039 / D3039M
ASTM D3039 determines the in-plane tensile properties of polymer matrix composite materials reinforced by high-modulus fibers. A number of calculations can be made including ultimate tensile strength, ultimate tensile strain, tensile chord modulus of
1964
[Page extract]
BS EN 12311-2
BS EN 12311-2 is a test method for determining the tensile properties of flexible sheets used for waterproofing roofs.
1966
[Page extract]
ASTM D3577
1. Scope ... 1.1 This specification describes certain requirements for packaged sterile rubber surgical gloves used in conducting surgical procedures.
1967
[Page extract]
ISO 20502
SO 20502:2005 describes a method of testing ceramic coatings by scratching with a diamond stylus.
1968
[Page extract]
ASTM D413-98
ASTM D413 is a test method used to determine the force per unit width required to separate a rubber layer from a flexible substrate such as fabric, wire or sheet metal.
1969
[Page extract]
ASTM D229
ASTM D229 is a test method, which provides useful engineering information for evaluating the mechanical behaviour of rigid electrical insulation at elevated temperature.
1970
[Page extract]
ISO 8364
ISO 8364:2007 specifies requirements and test methods for the binding mounting area and free space area, ski bindings and retention devices of alpine skis, in order to optimize the compatibility of the functional unit "ski binding - retention device - b
1971
[Page extract]
BS EN 1607
This European Standard specifies the equipment and procedures for determining the tensile strength of a product perpendicular to its faces. It is applicable to thermal insulating products.
1972
[Page extract]
ASTM D2105
ASTM D2105 determines the comparative longitudinal tensile properties of fiberglass pipe when tested under defined conditions of pretreatment, temperature, and testing machine speed.
1973
[Page extract]
ISO 7886-3
This document specifies the properties and performance of sterile single-use hypodermic syringes with an auto-disable syringe feature intended to deliver a fixed dose of vaccine immediately after filling.
1975
[Page extract]
ISO 7622-1
ISO 7622-1 specifies a method for the determination of the elongation of steel cords constituting the carcass of conveyor belts, when subjected to a force corresponding to 10 % and 60 % of the specified tensile strength.