Search results
1326
[Page extract]
ASTM D3470
This test method covers the determination of the force required to cause a downward-force-while-turning lug-finish closure to be rotated across the container finish lugs (strippage) without downward force being applied to the closure (Type IIA closures)
1328
[Page extract]
ASTM F2878-10
This test method is used for determining the force required to cause a hypodermic needle to penetrate through protective clothing material.
1329
[Page extract]
SAE USCAR-21-4
This specification defines test methods and requirements for validation of solderless crimped connections.
1330
Event
WestPack Expo 2025
Lansmont - together with our sister brand Mecmesin - will be participating in the upcoming WestPack trade show!
1331
[Page extract]
ASTM E1820-18ae1
The ASTM E1820 test method covers procedures and guidelines for the determination of fracture toughness of metallic materials using the following parameters: K, J, and CTOD (δ). Toughness can be measured in the R-curve format or as a point value.
1334
[Page extract]
BS EN ISO 844
ISO 844 specifies a method of determining a) the compressive strength and corresponding relative deformation, or b) the compressive stress at 10 % relative deformation, and c) when desired, the compressive modulus of rigid cellular plastics.
1335
[Page extract]
ASTM D1578
Significance and Use
Test Method D1578 for testing any spun yarn for breaking strength is considered satisfactory for acceptance testing of commercial shipments since the method has been used extensively in the trade.
1336
[Page extract]
BS EN ISO 376
BS EN ISO 376:2011 looks at the calibration of force-proving instruments used for the static verification of uniaxial testing equipment. These include tension and compression testing machines.
1337
[Page extract]
ASTM C297
This test method determines the flatwise tensile strength of the core, the core-to-facing bond, or the facing of an assembled sandwich panel.
1338
Event
180 Peel Testing Webinar (9 Feb. 2022)
Across many households and industries, consumers have developed a strong preference for and confidence in ‘Duct Tape’ for all types of uses and applications. This is mainly due to the adhesion strength.
1339
Event
Introduction to Consumer Packaging Testing
Damaged packaging can not only cost money but also impact brand perception. Consumers are less likely to purchase a product with damaged packaging, or if their product arrives damaged from poor packaging during the shipping and transport process.
1340
[Page extract]
Jewellery & Watch
In jewellery and watch production, alloys, components and other materials must meet the needs of the manufacturing process and the end-product should give good service performance when worn by the customer.
1341
Product
Máy kiểm tra mài mòn và viên thuốc
Martindale
902-964
Máy kiểm tra mài mòn và đóng cặn Martindale với TestWise Touch ™, có sẵn lên đến 9 trạm và có thể thích ứng để kiểm tra nhiều loại ứng dụng bao gồm hàng dệt, tất, da, bọc ghế, thảm, gỗ và cổ áo sơ mi. Được phát triển bởi công ty chị em của chúng tôi,…
1342
[Page extract]
Why Mecmesin for pull-off and pull-out testing
Mecmesin designs and manufactures tensile and adhesion testing equipment for both destructive and non-destructive pull-off and pull-out applications.
1343
[Page extract]
Case studies and practical applications
Screw-cap torque test on PET bottles
A beverage manufacturer identified inconsistencies in bridge torque linked to capping machine variability.
1344
[Page extract]
Standards for compressive hardness testing
Internationally recognised standards ensure that compressive hardness tests are accurate, repeatable, and comparable.
1345
[Page extract]
The role of ECT in quality assurance
The Edge Crush Test is a widely used measure for predicting box stacking performance.
1346
[Page extract]
Why is the 135° peel test important?
Seal strength testing plays a vital role in packaging quality control.
1347
[Page extract]
Why Mecmesin for bulk analysis
Expert engineering and equipment
Mecmesin systems are designed for precision and reliability in bulk testing applications.
1348
[Page extract]
What is the 135° peel test?
The 135° peel test is a method for measuring the seal strength of semi-rigid packaging, typically where a flexible lid is sealed onto a rigid or vacuum-formed container.
1349
[Page extract]
Why choose Mecmesin for test calculations and automation
Proven expertise in force and torque testing
Mecmesin has decades of experience in precision mechanical testing.
1350
[Page extract]
Standards for top-load testing
ASTM D2659
Specifies the method for determining the column crush resistance of blown thermoplastic containers.