Search results
651
[Page extract]
TAPPI T 838
This method describes a procedure for determining the edgewise compressive strength, parallel to the flutes, of a short column of singe, double, or triple-wall corrugated fiberboard, in a neckdown, non reinforced, loading edge configuration.
652
Event
Mecmesin Webinar: Introduction to consumer packaging testing
In the competitive world of consumer goods, damaged packaging isn't just a financial setback—it can tarnish your brand's reputation.
Customers are far less likely to choose a product with compromised packaging or one that arrives damaged due
653
[Page extract]
ASTM D6415 / D6415M-06a
ASTM D6415 is designed to measure the curved beam strength properties of fiber reinforced composites using a 90˚ curved beam specimen. The curved beam strength represents the moment per unit width which causes a delamination to form.
655
[Page extract]
BS EN 3841-509
This standard specifies a method of determining the forces required to insert and extract the contact pin into and out of the terminal socket of the signal contact. It shall be used together with EN 3841-100.
656
[Page extract]
ASTM D3950
This specification covers nonmetallic strapping and joining methods for closing, reinforcing, and bundling materials for shipment, unitizing, palletizing, and bracing for car and truck loading.
657
[Page extract]
Jaws
Choosing the most appropriate jaw type for a tensile grip can be tricky. It is a balance between having sufficient hold of the specimen to prevent it slipping and not having too ‘aggressive’ a hold which damages the specimen.
658
Event
Introduction to consumer packaging testing
In the competitive world of consumer goods, damaged packaging isn't just a financial setback—it can tarnish your brand's reputation.
659
[Page extract]
ASTM D622-99
ASTM D622 is a test method intended for use in testing the conventional types of hose employed for the operation of air brake and vacuum brake systems, either on a single motor vehicle or as connecting or transmission lines in a combination of vehicles<
660
[Page extract]
ASTM F2606-08
This guide can be used to obtain force versus deflection or midspan bending moment versus midspan curvature curves for stents and stent systems subjected to three-point bending conditions.
661
Event
Materials Testing: Theory and Practice Pt. 1
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
662
[Page extract]
ASTM B533
The force required to separate a metallic coating from its plastic substrate is determined by the interaction of several factors: the generic type and quality of the plastic molding compound, the molding process, the process used to prepare the substrat
663
[Page extract]
ISO 4674-1
Describes two methods for determining the forces necessary to initiate and propagate tearing of a coated fabric using the constant rate of tear method. The methods described are:
method A: tongue tear
method B: trouser tear
664
[Page extract]
FAQs about shear modulus
How is shear modulus tested?
Shear modulus is measured through torsion testing or shear testing fixtures applied to solid or bonded samples.
665
Software
Supporto motorizzato Force VectorPro Lite
Software VectorPro® Lite Disponibile come extra opzionale per i tester di forza motorizzati Mecmesin, VectorPro Lite è un pacchetto software avanzato per l'acquisizione e la stampa di dati. Richiama le routine di prova pre-memorizzate per le prove…
666
Software
Supporto motorizzato Torque VectorPro Lite
Software VectorPro® Lite Disponibile come optional per il tester di coppia motorizzato Vortex-dV di Mecmesin, VectorPro Lite è un pacchetto software avanzato per l'acquisizione e la stampa di dati. Richiama le routine di test pre-memorizzate,…
667
[Page extract]
Energy
Mecmesin has long been providing force and torque testing solutions to suppliers and contractors into the energy industry...
668
[Page extract]
ASTM F2923
This specification establishes requirements and test methods for specified elements and certain mechanical hazards in children's jewelry.
670
Software
VectorPro Lite force motorised stand
VectorPro® Lite software
Available as an optional extra to Mecmesin’s motorised force testers, VectorPro Lite is an advanced data acquisition and plotting software package. Call-up pre-stored test routines for tensile and compression testing, present test…
671
Software
VectorPro Lite torque motorised stand
VectorPro® Lite software
Available as an optional extra to Mecmesin’s Vortex-dV motorised torque tester, VectorPro Lite is an advanced data acquisition and plotting software package. Call-up pre-stored test routines, present test data graphically and…
672
Software
VectorPro MT software
VectorPro® MT software
VectorPro MT is an advanced materials testing software package developed to perform tensile, shear, bend and compression tests on a whole array of materials. Present measurement data graphically and issue customised test reports.…
673
Software
VectorPro force testing software
VectorPro® software
VectorPro is our advanced force testing software package developed to perform tensile, shear, bend and compression tests on materials, components and products. Present measurement data graphically and share customised test reports…
674
[Page extract]
Jewellery & Watch
In jewellery and watch production, alloys, components and other materials must meet the needs of the manufacturing process and the end-product should give good service performance when worn by the customer.
675
Sensor
Sensors - Helixa
Torque sensors
The HTC range of interchangeable torque sensors are specially adapted for the Helixa test system. Plug and play for automatic calibration with availability to suit all requirements in capacities from 0.1 N.m (0.9 lbf.in) to 6 N.m (50 lbf.in…