Search results
576
Case study
Prova di resistenza alla trazione del componente in plastica
Requisiti Il cliente produce collegamenti in plastica rigida che, una volta assemblati, formano un trasportatore.
577
Software
VectorPro MT software
VectorPro® MT software
VectorPro MT is an advanced materials testing software package developed to perform tensile, shear, bend and compression tests on a whole array of materials. Present measurement data graphically and issue customised test reports.…
578
[Page extract]
Manual test stands
Manual test stands allow simple force testing when budgets are limited.
Lever-operated models enable rapid testing of tension and compression up to 500 N.
579
[Page extract]
Motorised torque test stands
Repeatable torque testing
Looking for a motorised torque testing system to improve the accuracy and repeatability of your measurements compared to manual torque testers?
580
[Page extract]
ASTM D2646
These test methods may be used for acceptance testing of commercial shipments; however, caution is advised because information about between interlaboratory precision is incomplete. Comparative tests as directed in 5.1.1 may be advisable.
581
Case study
La polizia forza la manipolazione manuale e l'abbigliamento protettivo
Requisiti Una delle principali forze di polizia del Regno Unito richiede a tutte le nuove reclute di superare un "Job Related Fitness Test" (JRFT), per garantire che siano in grado di soddisfare le esigenze fisiche fiscali del ruolo
582
[Page extract]
Sistemi di forza controllati da software
Potenza sofisticata facile da usare I tester di trazione semi-automatici migliorano l'accuratezza e la ripetibilità delle misurazioni rispetto ai misuratori di forza manuali.
584
Accessory
V-jaws for Mec240g U-Form Vice Grip, 5 kN, for round sample Ø 5-50 mm
Mec240g-BV5
V-Jaws (5-50mm diameter) - nickel-plated having a hardened steel surface of 1.2mm pitch teeth to create a V-shaped groove.
For round samples where flat jaws do not provide enough surface contact (e.g. wires, rods,
tubes)
Supplied as 0.5 set = 2 jaws (…
585
Accessory
V-jaws for Mec240g U-Form Vice Grip, 5 kN, for round sample Ø 5-50 mm
Mec240g-BV5
V-Jaws (5-50mm diameter) - nickel-plated having a hardened steel surface of 1.2mm pitch teeth to create a V-shaped groove.
For round samples where flat jaws do not provide enough surface contact (e.g. wires, rods,
tubes)
Supplied as 0.5 set = 2 jaws (…
586
Accessory
V-jaws for Mec240g U-Form Vice Grip, 5 kN, for round sample Ø 2-50 mm
Mec240g-BV2
V-Jaws (2-50mm diameter) - nickel-plated having a hardened steel surface of 1.2mm pitch teeth to create a V-shaped groove.
For round samples where flat jaws do not provide enough surface contact (e.g. wires, rods, tubes)
Supplied as 0.5 set = 2 jaws (…
587
Accessory
V-jaws for Mec240g U-Form Vice Grip, 5 kN, for round sample Ø 2-50 mm
Mec240g-BV2
V-Jaws (2-50mm diameter) - nickel-plated having a hardened steel surface of 1.2mm pitch teeth to create a V-shaped groove.
For round samples where flat jaws do not provide enough surface contact (e.g. wires, rods, tubes)
Supplied as 0.5 set = 2 jaws (…
588
Accessory
V-jaws for Mec83 U-Form Pneumatic Vice Grip, 5 kN, for round sample Ø 6-10 mm
Mec83-BV6
V-Jaws (6-10mm diameter) - nickel-plated having a hardened steel surface of 1.2mm pitch teeth to create a V-shaped groove.
For round samples where flat jaws do not provide enough surface contact (e.g. wires, rods, tubes)
Supplied as 0.5 set = 2 jaws (…
589
Accessory
V-jaws for Mec83 U-Form Pneumatic Vice Grip, 5 kN, for round sample Ø 4-10 mm
Mec83-BV4
V-Jaws (4-10mm diameter) - nickel-plated having a hardened steel surface of 1.2mm pitch teeth to create a V-shaped groove.
For round samples where flat jaws do not provide enough surface contact (e.g. wires, rods, tubes)
Supplied as 0.5 set = 2 jaws (…
590
Case study
Test di piegatura a tre punti in schiuma da surf
Requisiti Un'azienda produttrice di grezzi per tavole da surf, realizzati in schiuma di poliuretano rigido (PU), intraprende un rigoroso programma di test per garantire la rigidità della schiuma e la resistenza del prodotto finale della t
591
[Page extract]
How wing tear testing is performed
Specimen geometry and preparation
Testing accuracy begins with correct specimen preparation. For wing tear tests, samples are cut into shapes with two projecting wings joined by a narrow central region where the tear initiates.
592
Case study
Cost effective cable strength testing
Customised engineering example
A major manufacturer of wire harnesses and connectors approached us for a cost-effective solution to pull-force test cables with different diameters having direct-bonded joints.
593
Case study
Toy testing to attachment strength safety standards
Requirement
The customer supplies plush giftware to retailers such as Clintons. Their plush products are manufactured to European toy safety standard BS EN 71-1:1998 (Safety of toys - Part 1: Mechanical and physical properties).
594
Case study
Card and paper crease line testing
Customised engineering example
A packaging production company needed to test the crease force of the ink-coated card used in their fully-enclosed cartons.
595
Event
Torque, force, and texture testing: How to elevate cosmetic quality standards
Cosmetic products require testing for objective texture analysis as well as the performance of applicators, dispensers, and packaging.
596
[Page extract]
Mechanical force gauges
Mechanical force gauges are spring-based instruments which feature a needle on a dial. They are entry-level push-pull gauges not requiring batteries so are intrinsically safe to use in hazardous environments.
597
Case study
Adjustable spectacles torque test
Customised engineering example
Adlens manufacture adaptive spectacle lenses, where the optical power is adjusted by a side dial which is then removed.
598
Page
Contact sales
Looking for the right testing solution?
Our experts are ready to help - just complete the form below and one of our Technical Sales Engineers will be in touch.
599
[Page extract]
ASTM F2193-02
These specifications and test methods provide standard specifications that specify material, labeling, and handling requirements for components used in surgical fixation of the spinal skeletal system such as metallic spinal screws, spinal plates, and sp
600
Case study
Sistemi di collaudo per i controlli dei commutatori automobilistici
Requisiti
I fornitori di sistemi elettrici per autoveicoli ai produttori OEM devono rispettare standard di qualità e prestazioni elevati per rimanere fornitori di alto livello.