Search results
2126
[Page extract]
SAE AIR 1471A
The purpose of this SAE Aerospace Information Report (AIR) is to provide the aerospace propulsion industry with recommended assembly torque limits for commonly used aircraft propulsion system threaded fasteners when a common torque value per fastener si
2127
Producto
Probadores de impacto de dardos que caen
Gama MEC-FD
MEC-FD1
La gama Mecmesin MEC-FD Falling Dart Impact Tester está diseñada para medir la resistencia al impacto o la tenacidad de las películas de plástico de conformidad con los métodos A y B de dardos de caída libre ASTM D1709 e ISO 77
2128
[Page extract]
ISO 20126
This International Standard specifies requirements and test methods for the physical properties of manual toothbrushes in order to promote the safety of these products for their intended use.It does not apply to manual interdental brushes and powered or
2129
[Page extract]
ASTM D1004
ASTM D1004-13 covers the determination of tear strength or tear resistance of flexible plastic film and sheeting. The site of tear is initiated by a high stress concentration caused by the 90° angle in the specimen.
2131
[Page extract]
BS EN 681-1
This standard specifies requirements for materials used in vulcanized rubber seals for:
1) cold potable water supply (up to 50®C);
2132
[Page extract]
*corp Coca-Cola SM-PR-2645
This test ensures that the column strength of non-refillable (NR) plastic bottles is sufficient to meet minimum performance specifications for vertical loading during peak load application.
2133
[Page extract]
BS EN ISO 10555-3
Catheters, Cannulas, Sterile equipment, Parenteral infusion equipment, Medical equipment, Medical instruments, Disposable, Marking, Flow rates, Force, Force measurement, Flow measurement, Test equipment, Testing conditions.
2134
[Page extract]
ASTM D1321
This test method covers the empirical estimation of the consistency of waxes derived from petroleum by measurement of the extent of penetration of a standard needle.
2135
[Page extract]
ISO 14126
ISO 14126 outlines procedures for determining the compressive properties of fibre-reinforced plastics composites in the in-plane direction. Two methods are detailed in the standard:
2136
[Page extract]
ISO 604
ISO 604 specifies a method for determining the compressive properties of plastics in the form of standard test specimens when tested under defined conditions of pretreatment, temperature, humidity and testing machine speed.
2137
[Page extract]
BS 6319-6
BS 6319-6 is a test method for determining the modulus of elasticity in compression of resin and polymer/cement compositions for use in construction.
2138
[Page extract]
ASTM D7137 / D7137M-17
ASTM D7137 is a test method that measures the compression residual strength properties of multidirectional polymer matrix composite laminated plates, which have been subjected to quasi-static indentation
2139
[Page extract]
ASTM D2659
ASTM D2659 determines the mechanical properties of blown thermoplastic containers under columnar crush conditions at a steady rate of compression. Any container, whether blown commercially or in the laboratory, may be used as the test specimen.
2141
[Page extract]
Energy
Mecmesin has long been providing force and torque testing solutions to suppliers and contractors into the energy industry...
2142
Caso de estudio
Prueba de material de Kevlar y chalecos a prueba de puñaladas
Requisito Kevlar® tiene muchas aplicaciones en el mundo moderno que van desde neumáticos de bicicleta, velas de carreras hasta guantes protectores y armaduras.
2143
[Page extract]
Construction
Mecmesin systems and gauges are designed for the application of international and industry standards for quality and safety...
2144
Producto
Dinamómetros mecánicos
Una solución sencilla para ensayos básicos de tracción y compresión aplicados a mano. Robustos dinamómetros mecánicos diseñados para ensayos pruebas generales de tensión y compresión de hasta 440 N. Fácil de usar con un dial analógico y un puntero de…
2145
Sensor
Sensors - Vortex-dV
Torque sensors
A range of 'Smart' interchangeable torque sensors are specially adapted for the Vortex-dV test system. Plug and play for automatic calibration and a range of capacities for all requirements, from 1.5 N.m (13 lbf.in) to 10 N.m (90 lbf.in).…
2146
Producto
Probador de torque de tapa de pantalla táctil
VTG Tornado
876-123
El probador de torque con pantalla táctil VTG Tornado es portátil y está clasificado como IP54 para probar el torque aplicado y de liberación de una amplia gama de productos. Mide hasta 10 Nm (90 lbf.in) para capturar la torsión de apertura y cierre de…
2149
[Page extract]
Automotive
Automotive engineering is a complex area incorporating elements of mechanical, electrical, software and safety engineering. Stringent performance and safety-critical criteria must be met to produce successful vehicles.