Search results
1576
[Page extract]
Modulus of elasticity formula
Young’s modulus (E) is calculated from the linear portion of a stress-strain curve using this formula:
1577
[Page extract]
Introduction to compressive shear testing
Compressive shear testing is a mechanical test method used to measure a material’s ability to resist shear forces while under compressive load.
1578
[Page extract]
Speak to an expert
Mecmesin has extensive experience in designing equipment and fixtures for adhesive bond strength testing.
1579
[Page extract]
Introduction to tensile strength
Tensile strength is a fundamental mechanical property that defines a material’s ability to resist forces that attempt to pull it apart. It represents the maximum tensile stress a material can withstand before failure.
1580
[Page extract]
Yield point testing methods
Yield point testing is most often performed using tensile testing, in which a specimen is subjected to a steadily increasing axial load until plastic deformation occurs.
1581
[Page extract]
Differences and similarities to other corrugated tests
While TAPPI T 824 focuses on the intrinsic crush strength of pre-fluted medium, other common corrugated tests measure different performance factors:
1582
[Page extract]
Công thức mô đun đàn hồi
Mô đun Young (E) được tính toán từ phần tuyến tính của đường cong ứng suất-biến dạng bằng công thức sau:
1583
[Page extract]
Applications across industries
T-peel testing is widely used in industries where adhesive bonds are critical:
1584
[Page extract]
Interpreting compressive strength test results
Interpreting results involves more than noting the peak load. Stress–strain curves reveal additional information such as modulus, yield point, and failure mode.
1585
[Page extract]
Thiết bị kiểm tra điểm chảy
Giải pháp đo điểm giới hạn chảy Các hệ thống kiểm tra tiên tiến như Mecmesin OmniTest và
1586
[Page extract]
Speak to an expert
Cleavage strength testing is essential for confirming material and adhesive performance in demanding applications.
1587
[Page extract]
Speak to an expert
Accurate and consistent tear testing is essential for maintaining product quality, meeting compliance requirements, and ensuring end-user satisfaction.
1588
[Page extract]
Tại sao nên sử dụng Mecmesin cho thử nghiệm kéo ra và kéo vào
Mecmesin thiết kế và sản xuất thiết bị kiểm tra độ bền kéo và độ bám dính cho cả ứng dụng kéo đứt và kéo rời phá hủy và không phá hủy.
1589
[Page extract]
What is fastening torque
Fastening torque refers to the rotational force applied to tighten a fastener, typically measured in Newton-metres (N·m) or pound-force inches (lbf·in). The correct torque value ensures adequate clamping without overstressing components.
1590
[Page extract]
Step-by-step test methodology
Preparation
Sample selection - Choose representative specimens, avoiding faults unless deliberately testing them.
Specimen cutting - Cut to standard dimensions with a central slit of specified
1591
[Page extract]
Dung dịch Mecmesin dùng cho thử nghiệm T-peel
Với nhiều thập kỷ kinh nghiệm trong lĩnh vực thử nghiệm vật liệu, Mecmesin cung cấp các hệ thống thử nghiệm bóc tách chữ T chính xác, có thể lặp lại, đáp ứng tiêu chuẩn ASTM D1876 ,
1592
[Page extract]
How to conduct a grab test
A standard grab test involves the following steps:
1593
[Page extract]
Tại sao nên chọn Mecmesin để chạy thử nghiệm mô-men xoắn
Với hơn 40 năm kinh nghiệm trong lĩnh vực đo mô-men xoắn chính xác, Mecmesin thiết kế và xây dựng các hệ thống đáp ứng yêu cầu khắt khe của các kỹ sư và chuyên gia chất lượng trên toàn thế
1594
[Page extract]
Introduction to torque testing
Torque testing is a vital part of packaging quality control.
1595
[Page extract]
Tại sao nên chọn Mecmesin để kiểm tra độ căng trong phân tích kết cấu
Mecmesin có hàng thập kỷ kinh nghiệm trong lĩnh vực kiểm tra độ bền kéo chính xác cho ngành công nghiệp thực phẩm và bao bì .
1596
[Page extract]
Standards for the peel wheel test
Standardisation ensures peel wheel tests are consistent and repeatable across laboratories and production sites.
1597
[Page extract]
Interpreting test results
Peel strength is typically reported in newtons per metre (N/m) or per 25 mm of bond width (N/25mm), depending on the industry standard. From the force-displacement graph, the following characteristics are analysed:
1598
[Page extract]
Speak to an expert
Selecting the right approach to secant modulus testing depends on the material, applicable standards, and the intended use of the results.
1599
[Page extract]
Understanding and interpreting test results
Box crush testing provides clear, measurable data to inform design and compliance decisions:
1600
[Page extract]
Measurement and testing methods
Techniques for measuring tangent modulus
Tangent modulus is measured during tensile or compression testing, w