Search results
2651
[Page extract]
ASTM D575-91
These test methods cover two test procedures for determining the compression-deflection characteristics of rubber compounds other than those usually classified as hard rubber and sponge rubber.
2653
[Page extract]
ISO 9856
ISO 9856 specifies a method for determining the elastic and permanent elongation of a conveyor belt and the calculation of the elastic modulus.
2654
[Page extract]
ASTM D3826
ASTM D3826 is a tensile test method, which covers a degradation-end point, or a brittle point) for degradable polyethylene/polypropylene films and sheeting less than 1.0 mm thick.
2655
[Page extract]
BS EN 12814-7
BS EN 12814-7 is a tensile test method with waisted test specimens for testing welded joints of thermoplastics semi-finished products.
2656
Case study
Peel testing Ostomy bags
Requirement
Salts Healthcare, a leading manufacturer and supplier of health care products required a low capacity system for testing the integrity of their hydrocolloid products.
2657
Event
Essentials of Cork Pull & Cork Elasticity Testing
Cork stoppers are extremely successful wine bottle closures that have been in use from ancient times.
2658
[Page extract]
BS EN ISO 8339
This International Standard specifies a method for the determination of the tensile properties of sealants used in joints in building construction.
2659
[Page extract]
EN TS 15945
The purpose of DD CEN/TS 15945 is to specify test methods to evaluate the ease of opening of consumer packages, in order to improve easy access to the contents. For packages regulated for safety or similar reasons, e.g.
2660
[Page extract]
BS ISO 2285
BS ISO 2285 is a test method for determining the tension set under constant elongation of vulcanised rubber or thermoplastic.
2661
[Page extract]
ASTM D7078/D7078M-12
This test method covers the determination of the shear properties of high-modulus fiber-reinforced composite materials by clamping the ends of a V-notched specimen between two pairs of loading rails.
2662
[Page extract]
ANSI/EIA 364
Mating and Unmating Procedure for Force Testing of Electrical Connectors and Sockets
2663
[Page extract]
FINAT FTM2
This test method differs from FTM 1 in that it can allow the end user to compare the repositionability of different laminates.
2664
[Page extract]
ASTM D6862-11
This test method is useful for acceptance and quality control testing. Adherends, application procedure, and sample conditioning shall be as agreed upon by the manufacturer and the user of the adherends and the adhesive.
2665
[Page extract]
BS EN ISO 13127
This standard is only to verify that panel-tested closures with minor modifications are still compliant, by applying mechanical tests as more economical than further full panel tests with children and with adults.
2666
[Page extract]
ISBT PTC-00004
These ISBT (International Society of Beverage Technologists) Sport Closure test methods focus on child safety related parameters such as separation forces and choking hazards of closure components.
2667
[Page extract]
ASTM C273/C273M
This test method is used to determine core shear properties of a sandwich construction material using loading plates bonded to the outer surfaces or skins (facesheets).
2668
Case study
Custom bottle cap mandrels
Customised engineering example
Plastic caps applied to bottles may be thin-walled and flexible, so that they become distorted when gripped by an operator during torque testing.
2670
[Page extract]
BS EN ISO 527-1
BS EN ISO 527-1 specifies the general principles for determining the tensile properties of plastics and plastic composites under defined conditions.
2671
[Page extract]
ASTM E855-08
This standard describes three test methods for determining the modulus of elasticity in bending and the bending strength of metallic strips or sheets intended for the use in flat springs.
2672
[Page extract]
ASTM D937-97
1.1 This test method covers measuring with a penetrometer the penetration of petrolatum as an empirical measure of consistency.
2673
[Page extract]
ISO 11502
Describes a qualitative and a quantitative method for assessing the tendency of flexible plastics films and sheets to adhere to one another when left in contact for some time, at a specified temperature and under light pressure.
2674
Specials
UTM FAQs
FAQs
How does the OmniTest universal testing machine compare in size and portability?
The OmniTest universal testing machine (UTM) offer
2675
[Page extract]
BS ISO 7322
This International Standard specifies test methods for the determination of the following characteristics of composition cork (= product obtained from the agglutination of cork granules with the addition of a binder generally not derived from cork cells