Search results
2476
[Page extract]
ISO 1926
ISO 1926 specifies a method of determining the behaviour of rigid cellular plastics materials when they are subjected to a tensile stress.
2477
[Page extract]
ISO 527-4
ISO 527-4 determines the tensile properties of isotropic and orthotropic fibre reinforced plastic composite sheeting and film including the tensile strength and modulus of elasticity, strain, elongation and the tensile energy to break (TEB).
2478
[Page extract]
ISO 10373-1
ISO/IEC 10373-1:2006 specifies the non-technology-specific test methods required to establish conformance of identification cards to the base (requirements) standards, for which the fundamental properties are defined in ISO/IEC 7810.
2479
[Page extract]
ISO 8067
ISO 8067 specifies two methods for the determination of the tear strength of flexible cellular polymeric materials:
Method A, using a trouser test piece
Method B, using an angle test piece without a nick
2480
[Page extract]
TAPPI T 818
The ring crush test correlates with edgewise compression strength of paperboard. This method is intended for paperbaord between 0.28mm (0.011 in.) and 0.51mm (0.020 in) thick.
2481
Case study
Lighting weld test
Requirement
A simple, low-cost fixture was specified by the customer for the Quality Control Laboratory. This was to hold a lighting assembly in a test where the welded contacts were pulled off.
2482
Case study
Prova di trazione su guarnizioni in gomma
Requisiti Le guarnizioni britanniche sono un importante produttore di guarnizioni, prodotti di tenuta e modanature. Questi sono realizzati con una varietà di materiali per soddisfare una vasta gamma di applicazioni.
2483
[Page extract]
ASTM D378
The ASTM D378 test method is used for evaluating the physical properties of flat conveyor belting, which are used in many industrial applications in which they are subjected to a great variety of stresses and conditions.
2484
Specials
Touchscreen Controller VectorPro
Touchscreen Controller
The Touchscreen Controller has been designed for use with the Twin-column OmniTest range of Materials Testers as an alternative to a desktop or laptop PC.
2485
[Page extract]
Compression
Compression tests are performed to evaluate the performance of a material or component under gradually increasing compressive load.
2486
[Page extract]
ISO 17454
ISO 17454 specifies a method for testing the adhesion between layers of multilayer pipes using a pulling test rig.
2487
[Page extract]
Special compression fixtures
Special compression fixtures have been specially designed to meet the challenges of a particular application.
2488
[Page extract]
BS EN ISO 13262
BS EN ISO 13262 is test method to determine the tensile strength of seams on thermoplastics spirally-formed structured-wall pipes.
2489
[Page extract]
ASTM E328-02
These test methods cover the determination of the time dependence of stress (stress relaxation) in materials and structures under conditions of approximately constant constraint, constant environment, and negligible vibration.
2490
[Page extract]
BS EN ISO 11608-3
Medical equipment, Medical instruments, Parenteral infusion equipment, Injection instruments, Injection guns, Syringes, Drug administration, Measuring cylinders, Containers, Performance testing, Performance, Leak tests, Design, Dimensions
2491
[Page extract]
BS EN ISO 22088-2
BS EN ISO 22088-2 is a test method for determining the environmental stress cracking of plastics.
This has replaced BS EN ISO 6252:1998
2492
[Page extract]
ASTM D4027-98
This test method describes equipment and procedures to measure the shear modulus and shear strength of adhesive layers between rigid adherends.
2493
[Page extract]
*corp 01M-01-216
To determine the maximum force required to rupture (break) a woven fabric – Rugby only
2494
[Page extract]
ISO 9073-7
Specifies a method for the determination of the bending length of nonwovens. Gives an equation for calculating the flexural rigity of the fabric from the bending length. Does not apply to composites and laminates.
2495
[Page extract]
ISO 15359
This International Standard specifies, a friction-testing method based on the horizontal plane principle, and the procedure for the determination of the static coefficient of friction before, and static and kinetic coefficients of friction after, a spec
2496
[Page extract]
PD CEN/TR 17394-3
This document defines a test method for security of attachment of functional and decorative metal mechanically applied press fasteners to children's clothing including for example gloves, hats, scarves, hosiery, ties, and textile belts.
2497
[Page extract]
BS EN 2243-2
This standard defines the general requirements for the determination of strength of structural adhesives by testing in peel metal to metal joints, at ambient or other temperatures.
2499
[Page extract]
ISO 9727-4
ISO 9727-4 specifies a test method for determining the percentage of diameter recovery of cylindrical cork stoppers, after compression.
2500
[Page extract]
ASTM D5321-12
This test method covers a procedure for determining the shear resistance of a geosynthetic against soil, or a geosynthetic against another geosynthetic, under a constant rate of deformation.