Search results
1651
[Page extract]
ASTM D1623
ASTM D1623 determines the tensile and tensile adhesion properties of rigid cellular plastics materials and foam. These are often used as insulation and structural materials in the aerospace, automotive and construction industries.
1652
[Page extract]
ASTM D6713-14
Materials shall be tested and the individual grades shall conform to specified values of the physical properties such as tensile strength, tensile elongation, tensile modulus, dimensional stability, flexural modulus, and Izod impact; and dimensional pro
1653
Case study
Car door closure effort
Requirement
When shutting car doors, users need to apply a certain force to initiate the movement and ensure a complete closure.
1654
[Page extract]
ASTM D1414
ASTM D1414 is used to measure the mechanical properties of vulcanized rubber o-rings. Mecmesin test equipment is relevant to the tensile testing part of this standard, which covers a variety of different tests.
1655
Page
Contact service
Need calibration or servicing support?
Whether it’s a Mecmesin product or another brand, our team can help. Complete the form below and one of our Service Engineers will get back to you.
1656
Event
Essentials of Adhesion (Peel) Testing
Across many households and industries, consumers have developed a strong preference for and confidence in ‘Duct Tape’ for all types of uses and applications. This is mainly due to the adhesion strength.
1657
[Page extract]
ASTM D380
ASTM D380 is a set of test methods for determining testing and inspection procedures for rubber hoses e.g. hydraulic hoses and automotive hoses.
1658
Case study
Mesure des caractéristiques du ressort de la pompe de carburant du moteur
Exigence
L'un des plus grands fabricants de pièces pour véhicules automobiles en République tchèque, faisant partie d'un grand groupe, doit tester un certain nombre de ses composants sous des forces élevées.
1659
[Page extract]
BS EN 12814-6
BS EN 12814-6 is a low temperature tensile test method for testing welded joints of thermoplastics semi-finished products.
1660
Case study
Seat belt locking device test
Requirement
The customer requested a system to measure the force required to release the locking mechanism of a car seat-belt whilst it is under tension.
1661
[Page extract]
BS EN 50081-1
This standard for emission requirements applies to electrical and electronic apparatus intended for use in the residential, commercial and light-industrial environment, as described in clause 5, for which no dedicated product or product-family emission
1662
[Page extract]
ISO 20344
This Standard specifies methods for testing footwear designed as personal protective equipment.
8 groups of tests from dimensions to mechanical properties and fluid resistance.
Supplemented by ISO 20345
1663
[Page extract]
ISO 11339
ISO 11339:2010 specifies a T‑peel test for the determination of the peel strength of an adhesive by measuring the peeling force of a T‑shaped bonded assembly of two flexible adherends. This test procedure does not provide design information.
1664
Case study
Tests de résistance sur câbles sertis
Exemple d'ingénierie sur mesure
Un important fabricant de câbles sertis et de connecteurs nous a demandé une solution économique pour des câbles d’essai de traction de différents diamètres comportant des sertissage à liaison directe.
1665
[Page extract]
ASTM D3916
ASTM D3916 is a test method for determining the tensile properties of pultruded, glass-fiber-reinforced thermosetting plastic rod of diameters ranging from 3.2 mm to 25.4 mm.
1666
[Page extract]
CETIE Guide 4
This document concerns the crowning process, using crown caps for which the seal is provided by a plastic liner, onto glass finishes adapted to either "pry-off" or "twist crown" applications.
1667
Case study
Force de fonctionnement de distributeur à pompe
Exemple d'ingénierie sur mesure
En tant que méthode de distribution de liquides et de pulvérisations, les propulseurs à spray, utilisant du gaz sous pression, sont évités pour de nombreuses raisons.
1668
[Page extract]
BS EN ISO 8295
ISO 8295 specifies a method for determining the coefficients of starting and sliding friction of plastics film and sheeting when sliding over the same or other substances. It is intended to be used for non-sticky plastic film and sheeting of up to appr
1669
Case study
Test de connexion des composants d'injection pour carburant
Exigence
Un certain nombre d'essais destructifs et non destructifs étaient nécessaires sur un assemblage en plastique utilisé dans un assemblage d'injection de carburant. Les tests comprennent:
1670
[Page extract]
ASTM D76-99
This specification covers operating characteristics of tensile testing machines for the determination of the force-elongation properties of textile materials.
1671
Case study
Force d'actionnement du distributeur à pompe
Exigence
Le client fabrique une gamme de pompes de dosage pour l'industrie cosmétique et de soins de beauté. Une exigence a été identifiée pour mesurer la force d'actionnement et la force de traction de la poignée de la pompe.
1672
[Page extract]
ASTM D7834-13
During the application of coatings, paint brushes can exhibit shedding of filling material onto the coated surface. A measure of this shedding filling material will determine the paint brush’s ability to resist shedding during application.
1673
Event
Automotive Component Torque Testing
This webinar will focus on the measurement of the torque resistance in knobs, switches, and torsion springs, which are among several components in automobiles that require testing to ensure quality, performance, and safety.
1674
Case study
Metal bottle cap on glass pull-off test
Customised engineering example
Gripping the base of a glass bottle for a tensile test can be challenging due to the slippy surface and contoured shape.
1675
[Page extract]
ASTM D3106
This test method covers the determination of the permanent deformation of bare, continuous elastomeric monofilaments and filament yarns made from rubber, spandex, anidex, or other elastomers subjected to prolonged periods of tension.