Search results
1326
[Page extract]
ASTM D5467 / D5467M-97
ASTM D5467 is a test method that determines the in-plane compressive properties of polymer matrix composite materials reinforced by high-modulus fibers in a sandwich beam configuration.
1327
[Page extract]
ASTM D6049-03
This test method is capable of measuring and characterizing the rheological behavior (viscosity and elasticity) of unvulcanized raw rubbers and rubber compounds, relating to the macro structure of rubber polymers (average molecular weight, molecular wei
1328
[Page extract]
CETIE Guide 4
This document concerns the crowning process, using crown caps for which the seal is provided by a plastic liner, onto glass finishes adapted to either "pry-off" or "twist crown" applications.
1329
[Page extract]
ASTM D4255 / D4255M-15a
ASTM D4255 is a test method for testing the in-plane shear properties of high-modulus fiber-reinforced composite materials. The method is divided into two procedures. Procedure A tests laminates clamped between two pairs of loading rails.
1330
[Page extract]
Key material testing standards
To ensure accuracy and comparability, elongation at break and tensile strength measurements are performed according to recognised industry standards.
1331
[Page extract]
ISO 36
ISO 36 determines the strength required to separate two plies of fabric bonded together with rubber, or a rubber and a fabric ply bonded together. This test is referred to as a “T-peel” test, because as the two adherends are pulled apart, they form the
1332
[Page extract]
BS EN ISO 9001
ISO 9001 has been revised to reflect the many changes in the way we now do business – new technology, greater access to information, higher customer expectations, globalization and increasing importance of service industries.
1333
[Page extract]
ASTM D3474
This standard covers the calibration and use of torque meters of the type normally used in packaging applications.
1334
Event
Essentials of Adhesion (Peel) Testing
Across many households and industries, consumers have developed a strong preference for and confidence in ‘Duct Tape’ for all types of uses and applications. This is mainly due to the adhesion strength.
1335
[Page extract]
Introduction to compressive modulus
Compressive modulus, also known as the modulus of elasticity in compression, is a key mechanical property describing a material’s ability to resist deformation under compressive load.
1336
[Page extract]
*corp 01M-01-217
To determine the maximum force required to rupture (break) a woven fabric.
1337
[Page extract]
FINAT FTM1
This test method is designed to quantify the permanence of adhesion or peelability of self-adhesive pressure sensitive) materials.
1338
[Page extract]
Industry-specific test standards
ISO 9895 - packaging materials
ISO 9895 specifies the method for determining the compressive strength of paper and b
1339
[Page extract]
Understanding cone penetration testing
Cone penetration testing is a precision method used to determine a material's resistance to penetration by a standardised cone-shaped probe under specific force conditions.
1340
[Page extract]
ASTM D4482-11
ASTM D4482 is a test method used to determine the fatigue life of rubber compounds undergoing a tensile-strain cycle. During part of the cycle, the strain is relaxed to a zero value.
1341
[Page extract]
ASTM C1368
This test method covers the determination of slow crack growth (SCG) parameters of advanced ceramics by using constant stress-rate rectangular beam flexural testing, or ring-on-ring biaxial disk flexural testing, or direct tensile strength, in which str
1343
Event
Pull Force and Break Strength Testing
Whether it is medical tubing, plastic straws, copper wire or zip ties, pull force and break strength testing is critical not only to production quality but also to consumer safety.
1344
[Page extract]
Torque testing methods
Programmable torque testers
Motorised torque testers allow engineers to define torque profiles, control rotational speed, and capture the complete torque-tension curve.
1345
[Page extract]
Torque testing standards
A range of recognised standards define the correct procedures for reverse ratchet torque testing, ensuring consistent and reliable results.
1346
Software
Vector OS (VFG/VFTI)
Vector OS
Our touchscreen instruments are powered by Vector OS, Mecmesin's technology platform for its latest force and torque test equipment. It delivers intuitive and customisable user interfaces, as well as advanced data acquisition and analysis.
To…
1347
[Page extract]
Introduction to ball burst strength testing
Ball burst testing measures the resistance of a material to rupture under localised force using a hemispherical probe.
1348
[Page extract]
Understanding tensile strength in testing
Both pull-off and pull-out testing measure tensile strength, which is the maximum load a specimen can sustain under tension before failure.
1349
[Page extract]
Standards for box crush testing
ASTM D642-00
This standard specifies methods for determining the compressive resistance of shipping containers, both filled and empty.