Search results
1701
[Page extract]
ISO 20344
This Standard specifies methods for testing footwear designed as personal protective equipment.
8 groups of tests from dimensions to mechanical properties and fluid resistance.
Supplemented by ISO 20345
1702
[Page extract]
ISO 11339
ISO 11339:2010 specifies a T‑peel test for the determination of the peel strength of an adhesive by measuring the peeling force of a T‑shaped bonded assembly of two flexible adherends. This test procedure does not provide design information.
1703
[Page extract]
ASTM D3916
ASTM D3916 is a test method for determining the tensile properties of pultruded, glass-fiber-reinforced thermosetting plastic rod of diameters ranging from 3.2 mm to 25.4 mm.
1704
[Page extract]
BS EN ISO 8295
ISO 8295 specifies a method for determining the coefficients of starting and sliding friction of plastics film and sheeting when sliding over the same or other substances. It is intended to be used for non-sticky plastic film and sheeting of up to appr
1705
[Page extract]
CETIE Guide 4
This document concerns the crowning process, using crown caps for which the seal is provided by a plastic liner, onto glass finishes adapted to either "pry-off" or "twist crown" applications.
1706
[Page extract]
ASTM D76-99
This specification covers operating characteristics of tensile testing machines for the determination of the force-elongation properties of textile materials.
1707
Event
Essentials of Adhesion (Peel) Testing
Across many households and industries, consumers have developed a strong preference for and confidence in ‘Duct Tape’ for all types of uses and applications. This is mainly due to the adhesion strength.
1708
[Page extract]
ASTM D7834-13
During the application of coatings, paint brushes can exhibit shedding of filling material onto the coated surface. A measure of this shedding filling material will determine the paint brush’s ability to resist shedding during application.
1709
Caso de estudio
Prueba de extracción del tubo de jeringa
Ejemplo de ingeniería personalizada Las pruebas de tracción por tracción requieren un agarre cuidadoso de las partes de separación para evitar deformarlas y, por lo tanto, debilitar artificialmente la junta.
1710
[Page extract]
ASTM D1414
ASTM D1414 is used to measure the mechanical properties of vulcanized rubber o-rings. Mecmesin test equipment is relevant to the tensile testing part of this standard, which covers a variety of different tests.
1711
Caso de estudio
Car door closure effort
Requirement
When shutting car doors, users need to apply a certain force to initiate the movement and ensure a complete closure.
1712
[Page extract]
ASTM D380
ASTM D380 is a set of test methods for determining testing and inspection procedures for rubber hoses e.g. hydraulic hoses and automotive hoses.
1713
Página
Contact service
Need calibration or servicing support?
Whether it’s a Mecmesin product or another brand, our team can help. Complete the form below and one of our Service Engineers will get back to you.
1714
[Page extract]
BS EN 12814-6
BS EN 12814-6 is a low temperature tensile test method for testing welded joints of thermoplastics semi-finished products.
1715
[Page extract]
BS EN 50081-1
This standard for emission requirements applies to electrical and electronic apparatus intended for use in the residential, commercial and light-industrial environment, as described in clause 5, for which no dedicated product or product-family emission
1716
Caso de estudio
Seat belt locking device test
Requirement
The customer requested a system to measure the force required to release the locking mechanism of a car seat-belt whilst it is under tension.
1717
Página
Enlace perdido
La página que solicitó no se encontró en este sitio. Podría haberse movido o algo salió mal.
1718
[Page extract]
ISO 374-4
This document specifies the test method for the determination of the resistance of protective glove materials to degradation by dangerous chemicals with continuous contact.
1719
[Page extract]
ISO 9664
The principle of the method specified is cyclically stressing the specimen in a way that may be regarded as the superposition of an alternating stress on a static stress which is the mean stress.
1720
[Page extract]
ASTM D1621
ASTM D1621 is used to measure the compressive properties of rigid cellular materials, particularly expanded plastics. Calculations include compressive strength, compressive strain, compressive stress and compressive modulus.
1721
[Page extract]
ASTM D6742 / D6742M
ASTM D6742 is the standard test method for tensile and compression testing of filled-hole polymer matrix composite laminates. It provides instructions for modifying open-hole tension and compression test methods to determine filled-hole tensile and com
1722
Event
Automotive Component Torque Testing
This webinar will focus on the measurement of the torque resistance in knobs, switches, and torsion springs, which are among several components in automobiles that require testing to ensure quality, performance, and safety.
1723
Caso de estudio
Metal bottle cap on glass pull-off test
Customised engineering example
Gripping the base of a glass bottle for a tensile test can be challenging due to the slippy surface and contoured shape.
1724
[Page extract]
ASTM D2918
This test method provides data for assessing the durabilities of adhesive joints by means of T-peel type specimens stressed in contact with air, air in equilibrium with certain solutions, water, aqueous solutions, or other environments at various temper
1725
[Page extract]
ASTM F37-00
1.1 These test methods provide a means of evaluating the sealing properties of sheet and solid form-in-place gasket materials at room temperature.