Search results
876
Caso de estudio
Bulk liquid carrier closures
Customised engineering example
Our client manufactures liquid bulk carriers fitted with two-part plastic valve closures. The collar is welded to a plastic bag, and the valve closure is fixed onto it by a compression joint.
877
Caso de estudio
Powdered drink container - compressive strength & lid peel tests
Customised engineering example
An international supplier of a powdered hot-chocolate drink wanted to test several aspects of their packaging. The powder is packed in a plastic-capped, foil-sealed cardboard tube container.
878
[Page extract]
ASTM D3578
Scope... 1.1 This specification describes certain requirements for natural rubber gloves used in conducting medical examinations and diagnostic and therapeutic procedures. It also covers natural rubber gloves used in handling contaminated medical
879
[Page extract]
Standards and compliance
ASTM D2063 defines methods for determining application and r
880
Event
Fundamentals of Compression Testing
Push or compressive testing helps determine the limits of most products that require constant pushing or compression.
881
Caso de estudio
Peel testing Ostomy bags
Requirement
Salts Healthcare, a leading manufacturer and supplier of health care products required a low capacity system for testing the integrity of their hydrocolloid products.
882
Caso de estudio
Mandril de cierre a prueba de niños (CRC)
Ejemplo de ingeniería personalizada Los cierres a prueba de niños (CRC) requieren suficiente fuerza vertical para activar el mecanismo de bloqueo CR antes de aplicar el torque.
883
[Page extract]
Standards and compliance
Commonly referenced standards for tangent modulus testing include:
884
[Page extract]
ASTM E1012-12e1
It has been shown that bending stresses that inadvertently occur due to misalignment between the applied force and the specimen axes during the application of tensile and compressive forces can affect the test results.
885
Caso de estudio
Automotive steering components
Customised engineering example
Sometimes the dimensions of a component make force testing difficult to perform. Our client needed to test the sliding force of a bearing along the complete length of an automotive steering rack.
886
Caso de estudio
90 degree peel test filter paper
Customised engineering example
Floating roller peel jigs are regularly used for testing laminates where the backing sheet is rigid and the facing sheet is flexible (e.g. security cards)
887
Caso de estudio
Catheter cap removal torque
Customised engineering example
Our client was testing the release torque of 20 mm long plastic catheter caps with irregular features to aid finger gripping.
888
Caso de estudio
Actuation force of touch screen
Requirement
Korean H Company (now JNTC), based in Korea, is a manufacturer of touch screens used for mobile, navigation and portable media player applications.
889
Caso de estudio
Hypodermic needle sharpness testing
Customised engineering example
Hypodermic needles are tested to determine how their design influences the ease of insertion into the skin, patient pain and skin trauma.
890
[Page extract]
Standards and best practices
BS EN ISO 8670-2 specifies methods for testing pressurised containers, including procedures for determining the pressure at which a container fails. It ensures testing is consistent, repeatable, and conducted safely.
891
Caso de estudio
Mandriles divididos para pruebas de par de cierre
Ejemplo de ingeniería personalizada Las superficies lisas de las tapas giratorias, usadas en botellas y frascos, requieren suficiente fuerza de agarre para evitar resbalones durante una prueba de torque, pero sin crear distorsión en la tapa.
892
Caso de estudio
Wine cork extraction test to ISO 9727-5
Requirement
The customer, AMORIM & IRMÃOS, S.A – Unidade Industrial da Valada, required an economic and easy-to-use system to test the extraction force of corks from glass wine bottles.
893
Event
Compressive Crush Force Testing
This webinar will focus on identifying and troubleshooting variables that impact compressive force testing, setting up repeatable compression force tests and establishing consistent testing standards for your products.
894
Caso de estudio
Usando un UTM como herramienta de calibración para células de carga
Requisito Cuando se trata de configurar y calibrar una celda de carga en tensión y compresión, este puede ser un proceso que consume mucho tiempo, particularmente cuando las cargas en cuestión son demasiado altas para usar un conjunto de pesa
895
Caso de estudio
Cardboard beverage bottle carrier unfolding
Customised engineering example
A manufacturer of fully-enclosed cartons wanted to quality test the fold-out force for a variety of their designs, used mainly to package drinks bottles and cans.
896
Caso de estudio
Torsion spring testing
Customised engineering example
Unlike most compression and tension springs, torsion springs are produced in a variety of forms with differing leg positions.
897
Caso de estudio
Diamante pull-off test
Requirement
The customer was a supplier to major UK clothing retailer Marks & Spencer, who stipulate that all fasteners and attachments must be tested to failure.
898
[Page extract]
Pruebas de fuerza
Los ensayos de fuerza son una forma de determinar cómo reaccionará un objeto cuando se somete a cargas de tracción o compresión, ya sea durante su funcionamiento normal o cuando se tira
899
Caso de estudio
Seat belt locking device test
Requirement
The customer requested a system to measure the force required to release the locking mechanism of a car seat-belt whilst it is under tension.
900
Caso de estudio
Medical suture device calibration system
Requirement
A number of devices which 'crimp' a curved needle to a fine medical thread needed to be tested. The crimp force was applied horizontally pulling a lever on the device.