Search results
801
Sensor
AFTI - Torque sensors
Torque sensors
The AFTI and AFG are versatile force and torque indicators designed for use with the Mecmesin range of 'Smart' static and rotary torque sensors.
Readings are displayed as live values with peak-hold function in both clockwise and counter-…
802
[Page extract]
ISO 1827
ISO 1827 specifies methods for the determination of the modulus in shear and the strength of bonds of rubber to metal or other rigid plates, using rubber bonded between four parallel plates.
803
[Page extract]
ASTM C1147
ASTM C1147 testing covers the evaluation of joints between two pieces of weldable grades of thermoplastic material. This testing is intended to establish methods to evaluate minimum short term weld factors.
804
[Page extract]
ISO 7623
ISO 7623 specifies a method for determining the bond strength of metal cords to their surrounding coating, either in the initial state or after thermal treatment.
805
[Page extract]
Motorised force test stands
Repeatable force testing
Looking for a motorised tensile or compression tester to improve the accuracy and repeatability of your measurements compared to manual force gauges?
806
[Page extract]
ASTM D2633
ASTM D2633 test methods cover procedures for the testing of thermoplastic insulations and jackets used on insulated wire and cable.
807
[Page extract]
BS 2782-3: 360C
BS 2782-3: Method 360C specifies a test method for testing the tear resistance of plastics film and sheeting by the initiation method
808
[Page extract]
BS EN 12814-2
BS EN 12814-2 is a tensile test method for testing welded joints of thermoplastics semi-finished products.
809
[Page extract]
ASTM D2370
This test method covers the determination of the elongation, tensile strength, and stiffness (modulus of elasticity) of organic coatings when tested as free films.
810
[Page extract]
BS EN ISO 13262
BS EN ISO 13262 is test method to determine the tensile strength of seams on thermoplastics spirally-formed structured-wall pipes.
811
Case study
Medical devices testing
Requirement
To provide a low cost, flexible tensile test machine which could be used in conjunction with special fixturing, to perform a range of functional and destructive tests on a range of products.
812
Case study
Car window sliding force tester
Requirement
Bridgestone TG Adelaide, a major supplier of rubber components to the automotive industry in Australia, needed to measure the frictional load associated with sliding a glass window between two rubber guides.
813
[Page extract]
BS ISO 5893
ISO 5893 specifies requirements for tensile-testing systems operating at constant rate of traverse and suitable for testing rubbers, plastics and adhesives, although any one system may only be applicable to a narrower range of materials.
814
[Page extract]
PSTC 8
Unwind adhesion is a quantitative measure of the degree of ease or difficulty in unwinding a roll of tape.
The test specimen shall be any 10 m (10 yard) or more roll of pressure sensitive tape - preferably 24 mm (1”) wide.
815
[Page extract]
ASTM D229
ASTM D229 is a test method, which provides useful engineering information for evaluating the mechanical behaviour of rigid electrical insulation at elevated temperature.
816
[Page extract]
ASTM D429-14
ASTM D429 is a test method used to determine the adhesion of rubber to metal substrates. It comprises 8 different tests: A through to H, covering tensile strength, peel and shear strength of the adhesion interface.
817
[Page extract]
ASTM C1424
This test method covers the determination of compressive strength including stress-strain behavior, under monotonic uniaxial loading of advanced ceramics at ambient temperature. This test method is restricted to specific test specimen geometries.
818
[Page extract]
ASTM D7137 / D7137M-17
ASTM D7137 is a test method that measures the compression residual strength properties of multidirectional polymer matrix composite laminated plates, which have been subjected to quasi-static indentation
819
[Page extract]
ASTM D3846
ASTM D3486 is a test method used for evaluating the in-plane strength of reinforced thermosetting plastics in flat sheet form in thicknesses ranging from 2.54 to 6.60 mm.
820
Case study
Hygienic disposal bin closure testing
Customised engineering example
A manufacturer of hygienic disposal bins came to us with a nappy (diaper) disposal unit fitted with a rotary intake mechanism.
821
[Page extract]
ASTM F1473-18
ASTM F1473 is a test method determines the resistance of polyethylene materials to slow crack growth. It is also known as PENT (Pennsylvania Notch Test) test.
822
Case study
Nursery toy product puncture resistance safety testing
Requirement
Wonderstar was established in 2010 in Thailand, with a mission of providing quality and well-designed baby products for families.
823
[Page extract]
ASTM D5766 / D5766-M
ASTM D5766 is a test method to determine the open-hole tensile strength of multidirectional polymer matrix composite laminates reinforced by high-modulus fibres.
824
[Page extract]
ASTM D3787
This test method describes the measurement for bursting strength with a ball burst strength tester of textiles or garments that exhibit a high degree of ultimate elongation.
825
Case study
Screw-cap torque test on PET bottles
Requirement
For over a century, Agua de Luso has been one of Portugal's most famous names in mineral water.